3421 lines
165 KiB
C++
3421 lines
165 KiB
C++
#include "digiSettingsPanel.h"
|
|
|
|
#include <QLabel>
|
|
#include <QFileDialog>
|
|
#include <QStyledItemDelegate>
|
|
#include <QToolTip>
|
|
#include <QPoint>
|
|
|
|
std::vector<std::pair<std::string, Reg>> infoIndex = {{"Serial Num : ", PHA::DIG::SerialNumber},
|
|
{"IP : ", PHA::DIG::IPAddress},
|
|
{"Model Name : ", PHA::DIG::ModelName},
|
|
{"FPGA version : ", PHA::DIG::FPGA_firmwareVersion},
|
|
{"DPP Type : ", PHA::DIG::FirmwareType},
|
|
{"CUP version : ", PHA::DIG::CupVer},
|
|
{"ADC bits : ", PHA::DIG::ADC_bit},
|
|
{"ADC rate [Msps] : ", PHA::DIG::ADC_SampleRate},
|
|
{"Num. of Channel : ", PHA::DIG::NumberOfChannel},
|
|
{"Input range [Vpp] : ", PHA::DIG::InputDynamicRange},
|
|
{"Input Type : ", PHA::DIG::InputType},
|
|
{"Input Impedance [Ohm] : ", PHA::DIG::InputImpedance}
|
|
};
|
|
|
|
QStringList LEDToolTip = { "LED_JESD_Y_PASS" ,
|
|
"LED_JESD_H_PASS" ,
|
|
"LED_DDR4_0_PASS" ,
|
|
"LED_DDR4_1_PASS" ,
|
|
"LED_DDR4_2_PASS" ,
|
|
"LEDFP_FAIL" ,
|
|
"LEDFP_NIM" ,
|
|
"LEDFP_TTL" ,
|
|
"LEDFP_DTLOSS" ,
|
|
"LEDFP_DTRDY" ,
|
|
"LEDFP_TRG" ,
|
|
"LEDFP_RUN" ,
|
|
"LEDFP_PLL_LOCK" ,
|
|
"LEDFP_CLKOUT" ,
|
|
"LEDFP_CLKIN" ,
|
|
"LEDFP_USB" ,
|
|
"LEDFP_SFP_SD" ,
|
|
"LEDFP_SFP_ACT" ,
|
|
"LEDFP_ACT" } ;
|
|
|
|
QStringList ACQToolTip = {"Armed",
|
|
"Run",
|
|
"Run_mw",
|
|
"Jesd_Clk_Valid",
|
|
"Busy",
|
|
"PreTriggerReady",
|
|
"LicenceFail" };
|
|
|
|
QStringList chToolTip = { "Channel signal delay initialization status (1 = initial delay done)",
|
|
"Channel time filter initialization status (1 = time filter initialization done)",
|
|
"Channel energy filter initialization status (1 = energy filter initialization done)",
|
|
"Channel full initialization status (1 = initialization done)",
|
|
"Reserved",
|
|
"Channel enable acquisition status (1 = acq enabled)",
|
|
"Channel inner run status (1 = run active)",
|
|
"Time-energy event free space status (1 = time-energy can be written)",
|
|
"Waveform event free space status (1 = waveform can be written)"};
|
|
|
|
QColor orangeColor(255, 165, 0);
|
|
|
|
DigiSettingsPanel::DigiSettingsPanel(Digitizer2Gen ** digi, unsigned short nDigi, QString analysisPath, QWidget * parent) : QWidget(parent){
|
|
|
|
setWindowTitle("Digitizers Settings");
|
|
setGeometry(0, 0, 1850, 1050);
|
|
//setSizePolicy(QSizePolicy::Expanding, QSizePolicy::Expanding);
|
|
|
|
this->digi = digi;
|
|
this->nDigi = nDigi;
|
|
if( nDigi > MaxNumberOfDigitizer ) {
|
|
this->nDigi = MaxNumberOfChannel;
|
|
qDebug() << "Please increase the MaxNumberOfChannel";
|
|
}
|
|
this->digiSettingPath = analysisPath + "/working/Settings/";
|
|
|
|
ID = 0;
|
|
enableSignalSlot = false;
|
|
QVBoxLayout * mainLayout = new QVBoxLayout(this); this->setLayout(mainLayout);
|
|
tabWidget = new QTabWidget(this); mainLayout->addWidget(tabWidget);
|
|
|
|
//@========================== Tab for each digitizer
|
|
for(unsigned short iDigi = 0; iDigi < this->nDigi; iDigi++){
|
|
|
|
QScrollArea * scrollArea = new QScrollArea(this);
|
|
scrollArea->setWidgetResizable(true);
|
|
scrollArea->setSizePolicy(QSizePolicy::Expanding, QSizePolicy::Expanding);
|
|
tabWidget->addTab(scrollArea, "Digi-" + QString::number(digi[iDigi]->GetSerialNumber()));
|
|
|
|
digiTab[iDigi] = new QWidget(tabWidget);
|
|
scrollArea->setWidget(digiTab[iDigi]);
|
|
|
|
QHBoxLayout * tabLayout_H = new QHBoxLayout(digiTab[iDigi]);
|
|
QVBoxLayout * tabLayout_V1 = new QVBoxLayout(); tabLayout_H->addLayout(tabLayout_V1);
|
|
QVBoxLayout * tabLayout_V2 = new QVBoxLayout(); tabLayout_H->addLayout(tabLayout_V2);
|
|
|
|
{//^====================== Group of Digitizer Info
|
|
QGroupBox * infoBox = new QGroupBox("Board Info", digiTab[iDigi]);
|
|
//infoBox->setSizePolicy(sizePolicy);
|
|
|
|
QGridLayout * infoLayout = new QGridLayout(infoBox);
|
|
tabLayout_V1->addWidget(infoBox);
|
|
|
|
const unsigned short nRow = 4;
|
|
for( unsigned short j = 0; j < (unsigned short) infoIndex.size(); j++){
|
|
QLabel * lab = new QLabel(QString::fromStdString(infoIndex[j].first), digiTab[iDigi]);
|
|
lab->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
leInfo[iDigi][j] = new QLineEdit(digiTab[iDigi]);
|
|
leInfo[iDigi][j]->setReadOnly(true);
|
|
|
|
Reg reg = infoIndex[j].second;
|
|
QString text = QString::fromStdString(digi[iDigi]->ReadValue(reg));
|
|
if( reg.GetPara() == PHA::DIG::ADC_SampleRate.GetPara() ) {
|
|
text += " = " + QString::number(digi[iDigi]->GetTick2ns(), 'f', 1) + " ns" ;
|
|
}
|
|
leInfo[iDigi][j]->setText(text);
|
|
infoLayout->addWidget(lab, j%nRow, 2*(j/nRow));
|
|
infoLayout->addWidget(leInfo[iDigi][j], j%nRow, 2*(j/nRow) +1);
|
|
}
|
|
}
|
|
|
|
{//^====================== Group Board status
|
|
QGroupBox * statusBox = new QGroupBox("Board Status", digiTab[iDigi]);
|
|
QGridLayout * statusLayout = new QGridLayout(statusBox);
|
|
statusLayout->setAlignment(Qt::AlignLeft);
|
|
statusLayout->setHorizontalSpacing(0);
|
|
|
|
tabLayout_V1->addWidget(statusBox);
|
|
|
|
//------- LED Status
|
|
QLabel * lbLED = new QLabel("LED status : ");
|
|
lbLED->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
statusLayout->addWidget(lbLED, 0, 0);
|
|
|
|
for( int i = 0; i < 19; i++){
|
|
LEDStatus[iDigi][i] = new QPushButton(digiTab[iDigi]);
|
|
LEDStatus[iDigi][i]->setEnabled(false);
|
|
LEDStatus[iDigi][i]->setFixedSize(QSize(30,30));
|
|
LEDStatus[iDigi][i]->setToolTip(QString::number(i) + " - " + LEDToolTip[i]);
|
|
LEDStatus[iDigi][i]->setToolTipDuration(-1);
|
|
//TODO set tooltip position on top
|
|
statusLayout->addWidget(LEDStatus[iDigi][i], 0, 19 - i);
|
|
|
|
}
|
|
|
|
//------- ACD Status
|
|
QLabel * lbACQ = new QLabel("ACQ status : ");
|
|
lbACQ->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
statusLayout->addWidget(lbACQ, 1, 0);
|
|
|
|
for( int i = 0; i < 7; i++){
|
|
ACQStatus[iDigi][i] = new QPushButton(digiTab[iDigi]);
|
|
ACQStatus[iDigi][i]->setEnabled(false);
|
|
ACQStatus[iDigi][i]->setFixedSize(QSize(30,30));
|
|
ACQStatus[iDigi][i]->setToolTip(QString::number(i) + " - " + ACQToolTip[i]);
|
|
ACQStatus[iDigi][i]->setToolTipDuration(-1);
|
|
statusLayout->addWidget(ACQStatus[iDigi][i], 1, 7 - i);
|
|
}
|
|
|
|
//------- Temperatures
|
|
QLabel * lbTemp = new QLabel("ADC Temperature [C] : ");
|
|
lbTemp->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
statusLayout->addWidget(lbTemp, 2, 0);
|
|
|
|
for( int i = 0; i < 8; i++){
|
|
leTemp[iDigi][i] = new QLineEdit(digiTab[iDigi]);
|
|
leTemp[iDigi][i]->setReadOnly(true);
|
|
leTemp[iDigi][i]->setAlignment(Qt::AlignHCenter);
|
|
statusLayout->addWidget(leTemp[iDigi][i], 2, 1 + 2*i, 1, 2);
|
|
}
|
|
|
|
QPushButton * bnUpdateStatus = new QPushButton("Update Status", this);
|
|
statusLayout->addWidget(bnUpdateStatus, 2, 19);
|
|
connect(bnUpdateStatus, &QPushButton::clicked, this, &DigiSettingsPanel::UpdateStatus);
|
|
|
|
for( int i = 0; i < statusLayout->columnCount(); i++) statusLayout->setColumnStretch(i, 0 );
|
|
}
|
|
|
|
{//^====================== Board Setting Buttons
|
|
QGridLayout * bnLayout = new QGridLayout();
|
|
tabLayout_V1->addLayout(bnLayout);
|
|
|
|
int rowId = 0;
|
|
//-------------------------------------
|
|
QLabel * lbSettingFile = new QLabel("Setting File : ", digiTab[iDigi]);
|
|
lbSettingFile->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
bnLayout->addWidget(lbSettingFile, rowId, 0);
|
|
|
|
leSettingFile[iDigi] = new QLineEdit(digiTab[iDigi]);
|
|
leSettingFile[iDigi]->setReadOnly(true);
|
|
leSettingFile[iDigi]->setText(QString::fromStdString(digi[iDigi]->GetSettingFileName()));
|
|
bnLayout->addWidget(leSettingFile[iDigi], rowId, 1, 1, 9);
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
bnReadSettngs[iDigi] = new QPushButton("Refresh Settings", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnReadSettngs[iDigi], rowId, 0, 1, 2);
|
|
connect(bnReadSettngs[iDigi], &QPushButton::clicked, this, &DigiSettingsPanel::RefreshSettings);
|
|
|
|
bnResetBd[iDigi] = new QPushButton("Reset Board", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnResetBd[iDigi], rowId, 2, 1, 2);
|
|
connect(bnResetBd[iDigi], &QPushButton::clicked, this, [=](){
|
|
SendLogMsg("Reset Digitizer-" + QString::number(digi[ID]->GetSerialNumber()));
|
|
digi[ID]->Reset();
|
|
RefreshSettings();
|
|
});
|
|
|
|
bnDefaultSetting[iDigi] = new QPushButton("Set Default Settings", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnDefaultSetting[iDigi], rowId, 4, 1, 2);
|
|
connect(bnDefaultSetting[iDigi], &QPushButton::clicked, this, &DigiSettingsPanel::SetDefaultPHASettigns);
|
|
|
|
bnSaveSettings[iDigi] = new QPushButton("Save Settings", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnSaveSettings[iDigi], rowId, 6, 1, 2);
|
|
connect(bnSaveSettings[iDigi], &QPushButton::clicked, this, &DigiSettingsPanel::SaveSettings);
|
|
|
|
bnLoadSettings[iDigi] = new QPushButton("Load Settings", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnLoadSettings[iDigi], rowId, 8, 1, 2);
|
|
connect(bnLoadSettings[iDigi], &QPushButton::clicked, this, &DigiSettingsPanel::LoadSettings);
|
|
|
|
//---------------------------------------
|
|
rowId ++;
|
|
bnClearData[iDigi] = new QPushButton("Clear Data", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnClearData[iDigi], rowId, 0, 1, 2);
|
|
connect(bnClearData[iDigi], &QPushButton::clicked, this, [=](){
|
|
digi[ID]->SendCommand(PHA::DIG::ClearData);
|
|
SendLogMsg("Digi-" + QString::number(digi[ID]->GetSerialNumber()) + "|Send Command : " + QString::fromStdString(PHA::DIG::ClearData.GetFullPara()));
|
|
UpdateStatus();
|
|
});
|
|
|
|
bnArmACQ[iDigi] = new QPushButton("Arm ACQ", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnArmACQ[iDigi], rowId, 2, 1, 2);
|
|
connect(bnArmACQ[iDigi], &QPushButton::clicked, this, [=](){
|
|
digi[ID]->SendCommand(PHA::DIG::ArmACQ);
|
|
SendLogMsg("Digi-" + QString::number(digi[ID]->GetSerialNumber()) + "|Send Command : " + QString::fromStdString(PHA::DIG::ArmACQ.GetFullPara()));
|
|
UpdateStatus();
|
|
});
|
|
|
|
bnDisarmACQ[iDigi] = new QPushButton("Disarm ACQ", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnDisarmACQ[iDigi], rowId, 4, 1, 2);
|
|
connect(bnDisarmACQ[iDigi], &QPushButton::clicked, this, [=](){
|
|
digi[ID]->SendCommand(PHA::DIG::DisarmACQ);
|
|
SendLogMsg("Digi-" + QString::number(digi[ID]->GetSerialNumber()) + "|Send Command : " + QString::fromStdString(PHA::DIG::DisarmACQ.GetFullPara()));
|
|
UpdateStatus();
|
|
});
|
|
|
|
bnSoftwareStart[iDigi] = new QPushButton("Software Start ACQ", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnSoftwareStart[iDigi], rowId, 6, 1, 2);
|
|
connect(bnSoftwareStart[iDigi], &QPushButton::clicked, this, [=](){
|
|
digi[ID]->SendCommand(PHA::DIG::SoftwareStartACQ);
|
|
SendLogMsg("Digi-" + QString::number(digi[ID]->GetSerialNumber()) + "|Send Command : " + QString::fromStdString(PHA::DIG::SoftwareStartACQ.GetFullPara()));
|
|
UpdateStatus();
|
|
});
|
|
|
|
bnSoftwareStop[iDigi] = new QPushButton("Software Stop ACQ", digiTab[iDigi]);
|
|
bnLayout->addWidget(bnSoftwareStop[iDigi], rowId, 8, 1, 2);
|
|
connect(bnSoftwareStop[iDigi], &QPushButton::clicked, this, [=](){
|
|
digi[ID]->SendCommand(PHA::DIG::SoftwareStopACQ);
|
|
SendLogMsg("Digi-" + QString::number(digi[ID]->GetSerialNumber()) + "|Send Command : " + QString::fromStdString(PHA::DIG::SoftwareStopACQ.GetFullPara()));
|
|
UpdateStatus();
|
|
});
|
|
|
|
//---------------
|
|
if( digi[iDigi]->IsDummy() || !digi[iDigi]->IsConnected() ){
|
|
bnReadSettngs[iDigi]->setEnabled(false);
|
|
bnResetBd[iDigi]->setEnabled(false);
|
|
bnDefaultSetting[iDigi]->setEnabled(false);
|
|
bnClearData[iDigi]->setEnabled(false);
|
|
bnArmACQ[iDigi]->setEnabled(false);
|
|
bnDisarmACQ[iDigi]->setEnabled(false);
|
|
bnSoftwareStart[iDigi]->setEnabled(false);
|
|
bnSoftwareStop[iDigi]->setEnabled(false);
|
|
}
|
|
|
|
}
|
|
|
|
|
|
{//^============================ Board Settings tab
|
|
|
|
QTabWidget * bdTab = new QTabWidget(digiTab[iDigi]);
|
|
tabLayout_V1->addWidget(bdTab);
|
|
|
|
{//^====================== Group Board settings
|
|
|
|
bdCfg[iDigi] = new QWidget(this);
|
|
bdTab->addTab(bdCfg[iDigi], "Board");
|
|
|
|
//digiBox[iDigi] = new QGroupBox("Board Settings", digiTab[iDigi]);
|
|
// //digiBox->setSizePolicy(sizePolicy);
|
|
QGridLayout * boardLayout = new QGridLayout(bdCfg[iDigi]);
|
|
boardLayout->setAlignment(Qt::AlignTop);
|
|
boardLayout->setSpacing(2);
|
|
//tabLayout_V1->addWidget(digiBox[iDigi]);
|
|
|
|
int rowId = 0;
|
|
//-------------------------------------
|
|
SetupComboBox(cbbClockSource[iDigi], PHA::DIG::ClockSource, -1, false, "Clock Source :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
QLabel * lbEnClockFP = new QLabel("Enable Clock Out Font Panel :", digiTab[iDigi]);
|
|
lbEnClockFP->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
boardLayout->addWidget(lbEnClockFP, rowId, 2, 1, 3);
|
|
|
|
cbbEnClockFrontPanel[iDigi] = new RComboBox(digiTab[iDigi]);
|
|
boardLayout->addWidget(cbbEnClockFrontPanel[iDigi], rowId, 5);
|
|
SetupShortComboBox(cbbEnClockFrontPanel[iDigi], PHA::DIG::EnableClockOutFrontPanel);
|
|
connect(cbbEnClockFrontPanel[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
//printf("%s %d %s \n", para.GetPara().c_str(), ch_index, cbb->currentData().toString().toStdString().c_str());
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::EnableClockOutFrontPanel.GetPara());
|
|
msg += " = " + cbbEnClockFrontPanel[ID]->currentData().toString();
|
|
if( digi[ID]->WriteValue(PHA::DIG::EnableClockOutFrontPanel, cbbEnClockFrontPanel[ID]->currentData().toString().toStdString())){
|
|
SendLogMsg(msg + "|OK.");
|
|
cbbEnClockFrontPanel[ID]->setStyleSheet("");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbbEnClockFrontPanel[ID]->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
QLabel * lbStartSource = new QLabel("Start Source :", digiTab[iDigi]);
|
|
lbStartSource->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbStartSource, rowId, 0);
|
|
|
|
for( int i = 0; i < (int) PHA::DIG::StartSource.GetAnswers().size(); i++){
|
|
ckbStartSource[iDigi][i] = new QCheckBox( QString::fromStdString((PHA::DIG::StartSource.GetAnswers())[i].second), digiTab[iDigi]);
|
|
boardLayout->addWidget(ckbStartSource[iDigi][i], rowId, 1 + i);
|
|
connect(ckbStartSource[iDigi][i], &QCheckBox::stateChanged, this, &DigiSettingsPanel::SetStartSource);
|
|
}
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
QLabel * lbGlobalTrgSource = new QLabel("Global Trigger Source :", digiTab[iDigi]);
|
|
lbGlobalTrgSource->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbGlobalTrgSource, rowId, 0);
|
|
|
|
for( int i = 0; i < (int) PHA::DIG::GlobalTriggerSource.GetAnswers().size(); i++){
|
|
ckbGlbTrgSource[iDigi][i] = new QCheckBox( QString::fromStdString((PHA::DIG::GlobalTriggerSource.GetAnswers())[i].second), digiTab[iDigi]);
|
|
boardLayout->addWidget(ckbGlbTrgSource[iDigi][i], rowId, 1 + i);
|
|
connect(ckbGlbTrgSource[iDigi][i], &QCheckBox::stateChanged, this, &DigiSettingsPanel::SetGlobalTriggerSource);
|
|
}
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbbTrgOut[iDigi], PHA::DIG::TrgOutMode, -1, false, "Trg-OUT Mode :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbbGPIO[iDigi], PHA::DIG::GPIOMode, -1, false, "GPIO Mode :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
//-------------------------------------
|
|
QLabel * lbAutoDisarmAcq = new QLabel("Auto disarm ACQ :", digiTab[iDigi]);
|
|
lbAutoDisarmAcq->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbAutoDisarmAcq, rowId, 4, 1, 2);
|
|
|
|
cbbAutoDisarmAcq[iDigi] = new RComboBox(digiTab[iDigi]);
|
|
boardLayout->addWidget(cbbAutoDisarmAcq[iDigi], rowId, 6);
|
|
SetupShortComboBox(cbbAutoDisarmAcq[iDigi], PHA::DIG::EnableAutoDisarmACQ);
|
|
connect(cbbAutoDisarmAcq[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
//printf("%s %d %s \n", para.GetPara().c_str(), ch_index, cbb->currentData().toString().toStdString().c_str());
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::EnableAutoDisarmACQ.GetPara());
|
|
msg += " = " + cbbAutoDisarmAcq[ID]->currentData().toString();
|
|
if( digi[ID]->WriteValue(PHA::DIG::EnableAutoDisarmACQ, cbbAutoDisarmAcq[ID]->currentData().toString().toStdString())){
|
|
SendLogMsg(msg + "|OK.");
|
|
cbbAutoDisarmAcq[ID]->setStyleSheet("");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbbAutoDisarmAcq[ID]->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbbBusyIn[iDigi], PHA::DIG::BusyInSource, -1, false, "Busy In Source :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
QLabel * lbStatEvents = new QLabel("Stat. Event :", digiTab[iDigi]);
|
|
lbStatEvents->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbStatEvents, rowId, 4, 1, 2);
|
|
|
|
cbbStatEvents[iDigi] = new RComboBox(digiTab[iDigi]);
|
|
boardLayout->addWidget(cbbStatEvents[iDigi], rowId, 6);
|
|
SetupShortComboBox(cbbStatEvents[iDigi], PHA::DIG::EnableStatisticEvents);
|
|
connect(cbbStatEvents[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::EnableStatisticEvents.GetPara());
|
|
msg += " = " + cbbStatEvents[ID]->currentData().toString();
|
|
if( digi[ID]->WriteValue(PHA::DIG::EnableStatisticEvents, cbbStatEvents[ID]->currentData().toString().toStdString()) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
cbbStatEvents[ID]->setStyleSheet("");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbbStatEvents[ID]->setStyleSheet("color:red");
|
|
}
|
|
});
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbbSyncOut[iDigi], PHA::DIG::SyncOutMode, -1, false, "Sync Out mode :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbbBoardVetoSource[iDigi], PHA::DIG::BoardVetoSource, -1, false, "Board Veto Source :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
QLabel * lbBdVetoWidth = new QLabel("Board Veto Width [ns] :", digiTab[iDigi]);
|
|
lbBdVetoWidth->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbBdVetoWidth, rowId, 3, 1, 2);
|
|
|
|
dsbBdVetoWidth[iDigi] = new RSpinBox(digiTab[iDigi], 0); // may be QDoubleSpinBox
|
|
dsbBdVetoWidth[iDigi]->setMinimum(0);
|
|
dsbBdVetoWidth[iDigi]->setMaximum(34359738360);
|
|
dsbBdVetoWidth[iDigi]->setSingleStep(20);
|
|
dsbBdVetoWidth[iDigi]->SetToolTip();
|
|
boardLayout->addWidget(dsbBdVetoWidth[iDigi], rowId, 5);
|
|
connect(dsbBdVetoWidth[iDigi], &RSpinBox::valueChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
dsbBdVetoWidth[ID]->setStyleSheet("color:blue;");
|
|
});
|
|
connect(dsbBdVetoWidth[iDigi], &RSpinBox::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
//printf("%s %d %d \n", para.GetPara().c_str(), ch_index, spb->value());
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::BoardVetoWidth.GetPara());
|
|
msg += " = " + QString::number(dsbBdVetoWidth[iDigi]->value());
|
|
if( digi[ID]->WriteValue(PHA::DIG::BoardVetoWidth, std::to_string(dsbBdVetoWidth[iDigi]->value()), -1) ){
|
|
dsbBdVetoWidth[ID]->setStyleSheet("");
|
|
SendLogMsg(msg + "|OK.");
|
|
}else{
|
|
dsbBdVetoWidth[ID]->setStyleSheet("color:red;");
|
|
SendLogMsg(msg + "|Fail.");
|
|
}
|
|
});
|
|
|
|
cbbBdVetoPolarity[iDigi] = new RComboBox(digiTab[iDigi]);
|
|
boardLayout->addWidget(cbbBdVetoPolarity[iDigi], rowId, 6);
|
|
SetupShortComboBox(cbbBdVetoPolarity[iDigi], PHA::DIG::BoardVetoPolarity);
|
|
connect(cbbBdVetoPolarity[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::BoardVetoPolarity.GetPara());
|
|
msg += " = " + cbbBdVetoPolarity[ID]->currentData().toString();
|
|
if( digi[ID]->WriteValue(PHA::DIG::BoardVetoPolarity, cbbBdVetoPolarity[ID]->currentData().toString().toStdString()) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
cbbBdVetoPolarity[ID]->setStyleSheet("");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbbBdVetoPolarity[ID]->setStyleSheet("color:red");
|
|
}
|
|
});
|
|
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupSpinBox(spbRunDelay[iDigi], PHA::DIG::RunDelay, -1, false, "Run Delay [ns] :", boardLayout, rowId, 0);
|
|
|
|
//-------------------------------------
|
|
QLabel * lbClockOutDelay = new QLabel("Temp. Clock Out Delay [ps] :", digiTab[iDigi]);
|
|
lbClockOutDelay->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbClockOutDelay, rowId, 3, 1, 2);
|
|
|
|
dsbVolatileClockOutDelay[iDigi] = new RSpinBox(digiTab[iDigi], 3);
|
|
dsbVolatileClockOutDelay[iDigi]->setMinimum(-18888.888);
|
|
dsbVolatileClockOutDelay[iDigi]->setMaximum(18888.888);
|
|
dsbVolatileClockOutDelay[iDigi]->setSingleStep(74.074);
|
|
dsbVolatileClockOutDelay[iDigi]->setValue(0);
|
|
dsbVolatileClockOutDelay[iDigi]->SetToolTip();
|
|
boardLayout->addWidget(dsbVolatileClockOutDelay[iDigi], rowId, 5);
|
|
connect(dsbVolatileClockOutDelay[iDigi], &RSpinBox::valueChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
dsbVolatileClockOutDelay[ID]->setStyleSheet("color:blue;");
|
|
});
|
|
connect(dsbVolatileClockOutDelay[iDigi], &RSpinBox::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
//printf("%s %d %d \n", para.GetPara().c_str(), ch_index, spb->value());
|
|
double step = dsbVolatileClockOutDelay[ID]->singleStep();
|
|
double value = dsbVolatileClockOutDelay[ID]->value();
|
|
dsbVolatileClockOutDelay[ID]->setValue( (std::round(value/step) * step) );
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::VolatileClockOutDelay.GetPara());
|
|
msg += " = " + QString::number(dsbVolatileClockOutDelay[iDigi]->value());
|
|
if( digi[ID]->WriteValue(PHA::DIG::VolatileClockOutDelay, std::to_string(dsbVolatileClockOutDelay[ID]->value()), -1) ){
|
|
dsbVolatileClockOutDelay[ID]->setStyleSheet("");
|
|
SendLogMsg(msg + "|OK.");
|
|
}else{
|
|
dsbVolatileClockOutDelay[ID]->setStyleSheet("color:red;");
|
|
SendLogMsg(msg + "|Fail.");
|
|
}
|
|
});
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbbIOLevel[iDigi], PHA::DIG::IO_Level, -1, false, "IO Level :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
QLabel * lbClockOutDelay2 = new QLabel("Perm. Clock Out Delay [ps] :", digiTab[iDigi]);
|
|
lbClockOutDelay2->setAlignment(Qt::AlignRight);
|
|
boardLayout->addWidget(lbClockOutDelay2, rowId, 3, 1, 2);
|
|
|
|
dsbClockOutDelay[iDigi] = new RSpinBox(digiTab[iDigi], 3);
|
|
dsbClockOutDelay[iDigi]->setMinimum(-18888.888);
|
|
dsbClockOutDelay[iDigi]->setMaximum(18888.888);
|
|
dsbClockOutDelay[iDigi]->setValue(0);
|
|
dsbClockOutDelay[iDigi]->setSingleStep(74.074);
|
|
dsbClockOutDelay[iDigi]->SetToolTip();
|
|
boardLayout->addWidget(dsbClockOutDelay[iDigi], rowId, 5);
|
|
connect(dsbClockOutDelay[iDigi], &RSpinBox::valueChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
dsbClockOutDelay[ID]->setStyleSheet("color:blue;");
|
|
});
|
|
connect(dsbClockOutDelay[iDigi], &RSpinBox::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
//printf("%s %d %d \n", para.GetPara().c_str(), ch_index, spb->value());
|
|
double step = dsbClockOutDelay[ID]->singleStep();
|
|
double value = dsbClockOutDelay[ID]->value();
|
|
dsbClockOutDelay[ID]->setValue( (std::round(value/step) * step) );
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::PermanentClockOutDelay.GetPara());
|
|
msg += " = " + QString::number(dsbClockOutDelay[iDigi]->value());
|
|
if( digi[ID]->WriteValue(PHA::DIG::PermanentClockOutDelay, std::to_string(dsbClockOutDelay[ID]->value()), -1) ){
|
|
dsbClockOutDelay[ID]->setStyleSheet("");
|
|
SendLogMsg(msg + "|OK.");
|
|
}else{
|
|
dsbClockOutDelay[ID]->setStyleSheet("color:red;");
|
|
SendLogMsg(msg + "|Fail.");
|
|
}
|
|
});
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupComboBox(cbDACoutMode[iDigi], PHA::DIG::DACoutMode, -1, false, "DAC out Mode :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupSpinBox(sbDACoutStaticLevel[iDigi], PHA::DIG::DACoutStaticLevel, -1, false, "DAC Static Lv. :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
//-------------------------------------
|
|
rowId ++;
|
|
SetupSpinBox(sbDACoutChSelect[iDigi], PHA::DIG::DACoutChSelect, -1, false, "DAC Channel :", boardLayout, rowId, 0, 1, 2);
|
|
|
|
connect(cbDACoutMode[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( cbDACoutMode[iDigi]->currentData().toString().toStdString() == "Static" ) {
|
|
sbDACoutStaticLevel[iDigi]->setEnabled(true);
|
|
}else{
|
|
sbDACoutStaticLevel[iDigi]->setEnabled(false);
|
|
}
|
|
});
|
|
|
|
connect(cbDACoutMode[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( cbDACoutMode[iDigi]->currentData().toString().toStdString() == "ChInput" ) {
|
|
sbDACoutChSelect[iDigi]->setEnabled(true);
|
|
}else{
|
|
sbDACoutChSelect[iDigi]->setEnabled(false);
|
|
}
|
|
});
|
|
|
|
connect(cbDACoutMode[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
if( cbDACoutMode[iDigi]->currentData().toString().toStdString() == "Square" ) {
|
|
bdTestPulse[iDigi]->setEnabled(true);
|
|
}else{
|
|
if( ckbGlbTrgSource[iDigi][3]->isChecked() == false ) bdTestPulse[iDigi]->setEnabled(false);
|
|
}
|
|
});
|
|
|
|
}
|
|
|
|
{//^====================== Test Pulse settings
|
|
|
|
bdTestPulse[iDigi] = new QWidget(this);
|
|
bdTab->addTab(bdTestPulse[iDigi], "Test Pulse");
|
|
QGridLayout * testPulseLayout = new QGridLayout(bdTestPulse[iDigi]);
|
|
testPulseLayout->setAlignment(Qt::AlignTop | Qt::AlignLeft);
|
|
testPulseLayout->setSpacing(2);
|
|
|
|
SetupSpinBox(dsbTestPuslePeriod[iDigi], PHA::DIG::TestPulsePeriod, -1, false, "Period [ns] :", testPulseLayout, 0, 0);
|
|
SetupSpinBox(dsbTestPusleWidth[iDigi], PHA::DIG::TestPulseWidth, -1, false, "Width [ns] :", testPulseLayout, 1, 0);
|
|
SetupSpinBox(spbTestPusleLowLevel[iDigi], PHA::DIG::TestPulseLowLevel, -1, false, "Low Lvl. [LSB] :", testPulseLayout, 2, 0);
|
|
SetupSpinBox(spbTestPusleHighLevel[iDigi], PHA::DIG::TestPulseHighLevel, -1, false, "High Lvl. [LSB] :", testPulseLayout, 3, 0);
|
|
|
|
dsbTestPuslePeriod[iDigi]->setFixedWidth(100);
|
|
dsbTestPusleWidth[iDigi]->setFixedWidth(100);
|
|
spbTestPusleLowLevel[iDigi]->setFixedWidth(100);
|
|
spbTestPusleHighLevel[iDigi]->setFixedWidth(100);
|
|
|
|
QLabel * lblow = new QLabel("", bdTestPulse[iDigi]); lblow->setAlignment(Qt::AlignCenter); testPulseLayout->addWidget(lblow, 2, 2);
|
|
QLabel * lbhigh = new QLabel("", bdTestPulse[iDigi]); lbhigh->setAlignment(Qt::AlignCenter); testPulseLayout->addWidget(lbhigh, 3, 2);
|
|
|
|
connect(spbTestPusleLowLevel[iDigi], &RSpinBox::valueChanged, this, [=](){
|
|
double value = spbTestPusleLowLevel[iDigi]->value();
|
|
lblow->setText("approx. " + QString::number(value/0xffff*2 - 1, 'f', 2) + " V");
|
|
});
|
|
|
|
connect(spbTestPusleHighLevel[iDigi], &RSpinBox::valueChanged, this, [=](){
|
|
double value = spbTestPusleHighLevel[iDigi]->value();
|
|
lbhigh->setText("approx. " + QString::number(value/0xffff*2 - 1, 'f', 2) + " V");
|
|
});
|
|
|
|
}
|
|
|
|
{//^====================== VGA settings
|
|
|
|
bdVGA[iDigi] = new QWidget(this);
|
|
bdTab->addTab(bdVGA[iDigi], "VGA Setting");
|
|
|
|
QGridLayout * vgaLayout = new QGridLayout(bdVGA[iDigi]);
|
|
//vgaLayout->setVerticalSpacing(0);
|
|
vgaLayout->setAlignment(Qt::AlignTop| Qt::AlignLeft);
|
|
|
|
for( int k = 0; k < 4; k ++){
|
|
SetupSpinBox(VGA[iDigi][k], PHA::VGA::VGAGain, k, false, "VGA-" + QString::number(k) + " [dB] :", vgaLayout, k, 0);
|
|
VGA[iDigi][k]->setSingleStep(0.5);
|
|
VGA[iDigi][k]->setFixedWidth(100);
|
|
VGA[iDigi][k]->SetToolTip();
|
|
|
|
}
|
|
}
|
|
|
|
{//^====================== ITL
|
|
bdITL[iDigi] = new QWidget(this);
|
|
bdTab->addTab(bdITL[iDigi], "ITL-A/B");
|
|
QGridLayout * ITLLayout = new QGridLayout(bdITL[iDigi]);
|
|
ITLLayout->setAlignment(Qt::AlignTop);
|
|
|
|
QGroupBox * gbITLA = new QGroupBox("ITL-A", bdITL[iDigi]);
|
|
ITLLayout->addWidget(gbITLA, 0, 0);
|
|
QGridLayout * aLayout = new QGridLayout(gbITLA);
|
|
|
|
SetupComboBox(cbITLAMainLogic[iDigi], PHA::DIG::ITLAMainLogic, -1, false, "Main Logic", aLayout, 0, 0);
|
|
SetupSpinBox( sbITLAMajority[iDigi], PHA::DIG::ITLAMajorityLev, -1, false, "Majority", aLayout, 1, 0);
|
|
SetupComboBox(cbITLAPairLogic[iDigi], PHA::DIG::ITLAPairLogic, -1, false, "Pair Logic", aLayout, 2, 0);
|
|
SetupComboBox(cbITLAPolarity[iDigi], PHA::DIG::ITLAPolarity, -1, false, "Polarity", aLayout, 3, 0);
|
|
SetupSpinBox( sbITLAGateWidth[iDigi], PHA::DIG::ITLAGateWidth, -1, false, "Output GateWidth [ns]", aLayout, 4, 0);
|
|
|
|
connect(cbITLAMainLogic[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
sbITLAMajority[iDigi]->setEnabled(cbITLAMainLogic[iDigi]->currentData().toString() == "Majority");
|
|
});
|
|
|
|
QGroupBox * gbITLB = new QGroupBox("ITL-B", bdITL[iDigi]);
|
|
ITLLayout->addWidget(gbITLB, 0, 1);
|
|
QGridLayout * bLayout = new QGridLayout(gbITLB);
|
|
|
|
SetupComboBox(cbITLBMainLogic[iDigi], PHA::DIG::ITLBMainLogic, -1, false, "Main Logic", bLayout, 0, 0);
|
|
SetupSpinBox( sbITLBMajority[iDigi], PHA::DIG::ITLBMajorityLev, -1, false, "Majority", bLayout, 1, 0);
|
|
SetupComboBox(cbITLBPairLogic[iDigi], PHA::DIG::ITLBPairLogic, -1, false, "Pair Logic", bLayout, 2, 0);
|
|
SetupComboBox(cbITLBPolarity[iDigi], PHA::DIG::ITLBPolarity, -1, false, "Polarity", bLayout, 3, 0);
|
|
SetupSpinBox( sbITLBGateWidth[iDigi], PHA::DIG::ITLBGateWidth, -1, false, "Output GateWidth [ns]", bLayout, 4, 0);
|
|
|
|
connect(cbITLBMainLogic[iDigi], &RComboBox::currentIndexChanged, this, [=](){
|
|
sbITLBMajority[iDigi]->setEnabled(cbITLBMainLogic[iDigi]->currentData().toString() == "Majority");
|
|
});
|
|
|
|
QGroupBox * gbITL = new QGroupBox("ITL-Connect", bdITL[iDigi]);
|
|
ITLLayout->addWidget(gbITL, 1, 0, 1, 2);
|
|
QGridLayout * cLayout = new QGridLayout(gbITL);
|
|
|
|
for( int i = 0; i < 32; i++){
|
|
if( i % 3 == 0 || i == 31){
|
|
QLabel * haha = new QLabel(QString::number(i), bdITL[iDigi]); cLayout->addWidget(haha, 0, i + 1);
|
|
}
|
|
}
|
|
|
|
QLabel * lb1 = new QLabel("ITL-A", bdITL[iDigi]);
|
|
cLayout->addWidget(lb1, 1, 0, 2, 1);
|
|
|
|
QLabel * lb2 = new QLabel("ITL-B", bdITL[iDigi]);
|
|
cLayout->addWidget(lb2, 4, 0, 2, 1);
|
|
|
|
QFrame *horizontalSeparator = new QFrame();
|
|
horizontalSeparator->setFrameShape(QFrame::HLine);
|
|
horizontalSeparator->setFrameShadow(QFrame::Sunken);
|
|
cLayout->addWidget(horizontalSeparator, 3, 0, 1, 33);
|
|
|
|
|
|
for( int i = 0; i < 64; i++){
|
|
chITLConnect[iDigi][i][0] = new QPushButton(bdITL[iDigi]);
|
|
chITLConnect[iDigi][i][0]->setFixedSize(15, 15);
|
|
cLayout->addWidget(chITLConnect[iDigi][i][0], 1 + i/32, i%32 + 1);
|
|
|
|
chITLConnect[iDigi][i][1] = new QPushButton(bdITL[iDigi]);
|
|
chITLConnect[iDigi][i][1]->setFixedSize(15, 15);
|
|
cLayout->addWidget(chITLConnect[iDigi][i][1], 4 + i/32, i%32 + 1);
|
|
|
|
connect(chITLConnect[iDigi][i][0], &QPushButton::clicked, this, [=](){
|
|
//printf(" %d ch %d clicked, %d \n", iDigi, i, ITLConnectStatus[iDigi][i]);
|
|
if( (ITLConnectStatus[iDigi][i] & 0x1) == 0 ){
|
|
ITLConnectStatus[iDigi][i] += 1;
|
|
chITLConnect[iDigi][i][0]->setStyleSheet("background-color : green;");
|
|
if( ((ITLConnectStatus[iDigi][i] >> 1) & 0x1) == 1 ) {
|
|
ITLConnectStatus[iDigi][i] -= 2;
|
|
chITLConnect[iDigi][i][1]->setStyleSheet("");
|
|
}
|
|
}else{
|
|
ITLConnectStatus[iDigi][i] -= 1;
|
|
chITLConnect[iDigi][i][0]->setStyleSheet("");
|
|
}
|
|
|
|
std::string value = "Disabled";
|
|
if( ITLConnectStatus[iDigi][i] == 1 ) value = "ITLA";
|
|
if( ITLConnectStatus[iDigi][i] == 2 ) value = "ITLB";
|
|
|
|
QString msg;
|
|
msg = "DIG:" + QString::number(digi[ID]->GetNChannels()) + ",CH:" + QString::number(i) + "|" + QString::fromStdString(PHA::CH::ITLConnect.GetPara() ) + " = " + QString::fromStdString(value);
|
|
if( digi[ID]->WriteValue(PHA::CH::ITLConnect, value, i) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
digi[ID]->ReadValue(PHA::CH::ITLConnect, i);
|
|
chITLConnect[iDigi][i][0]->setStyleSheet("background-color : red;");
|
|
}
|
|
|
|
});
|
|
|
|
connect(chITLConnect[iDigi][i][1], &QPushButton::clicked, this, [=](){
|
|
//printf(" %d ch %d clicked, %d \n", iDigi, i, ITLConnectStatus[iDigi][i]);
|
|
if( ((ITLConnectStatus[iDigi][i] >> 1) & 0x1) == 0 ){
|
|
ITLConnectStatus[iDigi][i] += 2;
|
|
chITLConnect[iDigi][i][1]->setStyleSheet("background-color : green;");
|
|
|
|
if( (ITLConnectStatus[iDigi][i] & 0x1) == 1 ) {
|
|
ITLConnectStatus[iDigi][i] -= 1;
|
|
chITLConnect[iDigi][i][0]->setStyleSheet("");
|
|
}
|
|
|
|
}else{
|
|
ITLConnectStatus[iDigi][i] -= 2;
|
|
chITLConnect[iDigi][i][1]->setStyleSheet("");
|
|
}
|
|
|
|
std::string value = "Disabled";
|
|
if( ITLConnectStatus[iDigi][i] == 1 ) value = "ITLA";
|
|
if( ITLConnectStatus[iDigi][i] == 2 ) value = "ITLB";
|
|
|
|
QString msg;
|
|
msg = "DIG:" + QString::number(digi[ID]->GetNChannels()) + ",CH:" + QString::number(i) + "|" + QString::fromStdString(PHA::CH::ITLConnect.GetPara() ) + " = " + QString::fromStdString(value);
|
|
if( digi[ID]->WriteValue(PHA::CH::ITLConnect, value, i) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
digi[ID]->ReadValue(PHA::CH::ITLConnect, i);
|
|
chITLConnect[iDigi][i][1]->setStyleSheet("background-color : red;");
|
|
}
|
|
});
|
|
|
|
}
|
|
|
|
}
|
|
|
|
{//^====================== LVDS
|
|
bdLVDS[iDigi] = new QWidget(this);
|
|
bdTab->addTab(bdLVDS[iDigi], "LVDS");
|
|
QGridLayout * LVDSLayout = new QGridLayout(bdLVDS[iDigi]);
|
|
LVDSLayout->setAlignment(Qt::AlignTop | Qt::AlignLeft);
|
|
//LVDSLayout->setSpacing(2);
|
|
|
|
for(int k = 0; k < 4; k ++){
|
|
SetupComboBox(cbLVDSMode[iDigi][k], PHA::LVDS::LVDSMode, k, false, "Ch-" + QString::number(16* k) + ":" + QString::number(16*(k+1)-1) + " Mode :", LVDSLayout, k, 0);
|
|
SetupComboBox(cbLVDSDirection[iDigi][k], PHA::LVDS::LVDSDirection, k, false, "Direction :", LVDSLayout, k, 2);
|
|
}
|
|
|
|
QLabel * lbIOReg = new QLabel("Status :", bdLVDS[iDigi]);
|
|
lbIOReg->setAlignment(Qt::AlignCenter | Qt::AlignRight);
|
|
LVDSLayout->addWidget(lbIOReg, 4, 0);
|
|
|
|
leLVDSIOReg[iDigi] = new QLineEdit(bdLVDS[iDigi]);
|
|
LVDSLayout->addWidget(leLVDSIOReg[iDigi], 4, 1, 1, 3);
|
|
connect(leLVDSIOReg[iDigi], &QLineEdit::textChanged, this, [=](){if( enableSignalSlot ) leLVDSIOReg[iDigi]->setStyleSheet("color: green;");});
|
|
connect(leLVDSIOReg[iDigi], &QLineEdit::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
std::string value = leLVDSIOReg[iDigi]->text().toStdString();
|
|
Reg para = PHA::DIG::LVDSIOReg;
|
|
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += " = " + leLVDSIOReg[iDigi]->text();
|
|
if( digi[ID]->WriteValue(para, value)){
|
|
SendLogMsg(msg + "|OK.");
|
|
leLVDSIOReg[iDigi]->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
leLVDSIOReg[iDigi]->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
}
|
|
|
|
{//^====================== Group = InputDelay
|
|
bdGroup[iDigi] = new QWidget(this);
|
|
bdTab->addTab(bdGroup[iDigi], "Input Delay");
|
|
QGridLayout * groupLayout = new QGridLayout(bdGroup[iDigi]);
|
|
groupLayout->setAlignment(Qt::AlignTop );
|
|
//LVDSLayout->setSpacing(2);
|
|
|
|
for(int k = 0; k < MaxNumberOfGroup; k ++){
|
|
SetupSpinBox(spbInputDelay[iDigi][k], PHA::GROUP::InputDelay, k, false, "ch : " + QString::number(4*k) + " - " + QString::number(4*k+3) + " [ns] ", groupLayout, k/4, 2*(k%4));
|
|
}
|
|
|
|
bdGroup[iDigi]->setEnabled(digi[iDigi]->GetCupVer() >= MIN_VERSION_GROUP);
|
|
}
|
|
|
|
}
|
|
|
|
{//^====================== Group channel settings
|
|
QGroupBox * chBox = new QGroupBox("Channel Settings", digiTab[iDigi]);
|
|
//chBox->setSizePolicy(sizePolicy);
|
|
tabLayout_V2->addWidget(chBox);
|
|
QGridLayout * chLayout = new QGridLayout(chBox); //chBox->setLayout(chLayout);
|
|
chBox->setFixedWidth(900);
|
|
|
|
chTabWidget[iDigi] = new QTabWidget(digiTab[iDigi]); chLayout->addWidget(chTabWidget[iDigi]);
|
|
|
|
if( digi[iDigi]->GetFPGAType() == DPPType::PHA ) SetupPHAChannels(iDigi);
|
|
if( digi[iDigi]->GetFPGAType() == DPPType::PSD ) SetupPSDChannels(iDigi);
|
|
|
|
{//@============== Status tab
|
|
QTabWidget * statusTab = new QTabWidget(digiTab[iDigi]);
|
|
chTabWidget[iDigi]->addTab(statusTab, "Status");
|
|
|
|
QGridLayout * layout = new QGridLayout(statusTab);
|
|
layout->setAlignment(Qt::AlignTop);
|
|
layout->setSpacing(0);
|
|
|
|
QLabel* lb0x = new QLabel("9-bit status", statusTab); lb0x->setAlignment(Qt::AlignHCenter); layout->addWidget(lb0x, 0, 1, 1, 9);
|
|
QLabel* lb0a = new QLabel("Gain Fact.", statusTab); lb0a->setAlignment(Qt::AlignHCenter); layout->addWidget(lb0a, 0, 10);
|
|
QLabel* lb1a = new QLabel("ADC->Volt", statusTab); lb1a->setAlignment(Qt::AlignHCenter); layout->addWidget(lb1a, 0, 11);
|
|
|
|
QLabel* lb1x = new QLabel("9-bit status", statusTab); lb1x->setAlignment(Qt::AlignHCenter); layout->addWidget(lb1x, 0, 13, 1, 9);
|
|
QLabel* lb0b = new QLabel("Gain Fact.", statusTab); lb0b->setAlignment(Qt::AlignHCenter); layout->addWidget(lb0b, 0, 22);
|
|
QLabel* lb1b = new QLabel("ADC->Volt", statusTab); lb1b->setAlignment(Qt::AlignHCenter); layout->addWidget(lb1b, 0, 23);
|
|
|
|
for( int ch = 0; ch < digi[iDigi]->GetNChannels(); ch ++){
|
|
QLabel * lb = new QLabel(" ch-" + QString::number(ch) + " ", statusTab);
|
|
lb->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
layout->addWidget(lb, 1 + ch/2, ch%2 * 12);
|
|
|
|
for( int k = 0 ; k < 9; k++){
|
|
chStatus[iDigi][ch][k] = new QPushButton(statusTab);
|
|
chStatus[iDigi][ch][k]->setEnabled(false);
|
|
chStatus[iDigi][ch][k]->setFixedSize(QSize(10,25));
|
|
chStatus[iDigi][ch][k]->setToolTip(QString::number(k) + " - " + chToolTip[k]);
|
|
chStatus[iDigi][ch][k]->setToolTipDuration(-1);
|
|
layout->addWidget(chStatus[iDigi][ch][k], 1 + ch/2, ch%2 * 12 + 9 - k); // arrange backward, so that it is like a bit-wise
|
|
}
|
|
|
|
chGainFactor[iDigi][ch] = new QLineEdit(statusTab);
|
|
chGainFactor[iDigi][ch]->setFixedWidth(100);
|
|
layout->addWidget(chGainFactor[iDigi][ch], 1 + ch/2, ch%2*12 + 10);
|
|
|
|
chADCToVolts[iDigi][ch] = new QLineEdit(statusTab);
|
|
chADCToVolts[iDigi][ch]->setFixedWidth(100);
|
|
layout->addWidget(chADCToVolts[iDigi][ch], 1 + ch/2, ch%2*12 + 11);
|
|
|
|
}
|
|
}
|
|
|
|
{//@============== Trigger Mask/Map tab
|
|
|
|
triggerMapTab[iDigi] = new QTabWidget(digiTab[iDigi]);
|
|
chTabWidget[iDigi]->addTab(triggerMapTab[iDigi], "Trigger Map");
|
|
|
|
QGridLayout * triggerLayout = new QGridLayout(triggerMapTab[iDigi]);
|
|
triggerLayout->setAlignment(Qt::AlignTop);
|
|
|
|
int rowID = 0;
|
|
//----------------------------
|
|
// SetupComboBox( cbAllEvtTrigger[iDigi], PHA::CH::EventTriggerSource, -1, false, "Event Trigger Source (all ch.)", triggerLayout, rowID, 0);
|
|
// SetupComboBox( cbAllWaveTrigger[iDigi], PHA::CH::WaveTriggerSource, -1, false, "Wave Trigger Source (all ch.)", triggerLayout, rowID, 2);
|
|
|
|
// //----------------------------
|
|
// rowID ++;
|
|
// SetupComboBox( cbAllCoinMask[iDigi], PHA::CH::CoincidenceMask, -1, false, "Coincident Mask (all ch.)", triggerLayout, rowID, 0);
|
|
// SetupSpinBox( sbAllCoinLength[iDigi], PHA::CH::CoincidenceLength, -1, false, "Coincident Length [ns] (all ch.)", triggerLayout, rowID, 2);
|
|
|
|
// //----------------------------
|
|
// rowID ++;
|
|
// SetupComboBox( cbAllAntiCoinMask[iDigi], PHA::CH::AntiCoincidenceMask, -1, false, "Anti-Coincident Mask (all ch.)", triggerLayout, rowID, 0);
|
|
|
|
QSignalMapper * triggerMapper = new QSignalMapper(digiTab[iDigi]);
|
|
connect(triggerMapper, &QSignalMapper::mappedInt, this, &DigiSettingsPanel::onTriggerClick);
|
|
|
|
//----------------------------
|
|
rowID ++;
|
|
QGroupBox * triggerBox = new QGroupBox("Trigger Mask", digiTab[iDigi]);
|
|
triggerLayout->addWidget(triggerBox, rowID, 0, 1, 4);
|
|
|
|
QGridLayout * tbLayout = new QGridLayout(triggerBox);
|
|
tbLayout->setAlignment(Qt::AlignCenter | Qt::AlignTop);
|
|
tbLayout->setSpacing(0);
|
|
|
|
//----------------------------
|
|
rowID = 0;
|
|
QLabel * instr1 = new QLabel("Reading: Column (C) represents a trigger channel for Row (R) channel.", digiTab[iDigi]);
|
|
instr1->setAlignment(Qt::AlignLeft);
|
|
tbLayout->addWidget(instr1, rowID, 0, 1, 64+15);
|
|
|
|
rowID ++;
|
|
QLabel * instr2 = new QLabel("For example, R3C1 = ch-3 trigger source is ch-1.", digiTab[iDigi]);
|
|
instr2->setAlignment(Qt::AlignLeft);
|
|
tbLayout->addWidget(instr2, rowID, 0, 1, 64+15);
|
|
|
|
rowID ++;
|
|
for( int j = 0; j < digi[iDigi]->GetNChannels(); j++){
|
|
if( j % 4 == 0) {
|
|
QLabel * lllb = new QLabel(QString::number(j), digiTab[iDigi]);
|
|
lllb->setAlignment(Qt::AlignLeft);
|
|
tbLayout->addWidget(lllb, rowID , 1 + j + j/4, 1, 4);
|
|
}
|
|
}
|
|
|
|
rowID ++;
|
|
int colID = 0;
|
|
for(int i = 0; i < digi[iDigi]->GetNChannels(); i++){
|
|
colID = 1;
|
|
|
|
if( i % 4 == 0){
|
|
QLabel * lllba = new QLabel(QString::number(i), digiTab[iDigi]);
|
|
lllba->setAlignment(Qt::AlignTop | Qt::AlignRight);
|
|
tbLayout->addWidget(lllba, 3 + i + i/4, 0, 4, 1);
|
|
}
|
|
|
|
for(int j = 0; j < digi[iDigi]->GetNChannels(); j++){
|
|
|
|
trgMap[iDigi][i][j] = new QPushButton(digiTab[iDigi]);
|
|
trgMap[iDigi][i][j]->setFixedSize(QSize(10,10));
|
|
trgMapClickStatus[iDigi][i][j] = false;
|
|
tbLayout->addWidget(trgMap[iDigi][i][j], rowID, colID);
|
|
|
|
triggerMapper->setMapping(trgMap[iDigi][i][j], (iDigi << 16) + (i << 8) + j);
|
|
connect(trgMap[iDigi][i][j], SIGNAL(clicked()), triggerMapper, SLOT(map()));
|
|
|
|
colID ++;
|
|
if( j%4 == 3 && j!= digi[iDigi]->GetNChannels() - 1){
|
|
QFrame * vSeparator = new QFrame(digiTab[iDigi]);
|
|
vSeparator->setFrameShape(QFrame::VLine);
|
|
tbLayout->addWidget(vSeparator, rowID, colID);
|
|
colID++;
|
|
}
|
|
}
|
|
|
|
rowID++;
|
|
if( i%4 == 3 && i != digi[iDigi]->GetNChannels() - 1){
|
|
QFrame * hSeparator = new QFrame(digiTab[iDigi]);
|
|
hSeparator->setFrameShape(QFrame::HLine);
|
|
tbLayout->addWidget(hSeparator, rowID, 1, 1, digi[iDigi]->GetNChannels() + 15);
|
|
rowID++;
|
|
}
|
|
}
|
|
}
|
|
|
|
} //=== end of channel group
|
|
|
|
} //=== end of digiTab[iDigi]
|
|
|
|
{//^============================================== Inquiry / Copy Tab
|
|
ICTab = new QTabWidget(this);
|
|
tabWidget->addTab(ICTab, "Inquiry / Copy");
|
|
|
|
QVBoxLayout * layout1 = new QVBoxLayout(ICTab);
|
|
layout1->setAlignment(Qt::AlignTop | Qt::AlignLeft);
|
|
|
|
{//@============== low level inquiry
|
|
icBox1 = new QGroupBox("Low Level Settings", ICTab);
|
|
layout1->addWidget(icBox1);
|
|
|
|
QGridLayout * inquiryLayout = new QGridLayout(icBox1);
|
|
inquiryLayout->setAlignment(Qt::AlignTop | Qt::AlignLeft);
|
|
//inquiryLayout->setSpacing(0);
|
|
|
|
int rowID = 0;
|
|
QLabel * info1 = new QLabel("This will read from the digitizer, save the setting to memory.", icBox1);
|
|
inquiryLayout->addWidget(info1, rowID, 0, 1, 6);
|
|
rowID ++;
|
|
QLabel * info2 = new QLabel("The settings from Digitizer Tab will not reflect immedinately in here.", icBox1);
|
|
inquiryLayout->addWidget(info2, rowID, 0, 1, 6);
|
|
|
|
///=========== header
|
|
rowID ++;
|
|
QLabel * hd0 = new QLabel("Digi. Value", icBox1);
|
|
hd0->setAlignment(Qt::AlignCenter);
|
|
inquiryLayout->addWidget(hd0, rowID, 3);
|
|
|
|
QLabel * hd1 = new QLabel("Unit", icBox1);
|
|
hd1->setAlignment(Qt::AlignCenter);
|
|
inquiryLayout->addWidget(hd1, rowID, 4);
|
|
|
|
QLabel * hd2 = new QLabel("<---------------------- Set Value ---------------------->", icBox1);
|
|
hd2->setAlignment(Qt::AlignCenter);
|
|
inquiryLayout->addWidget(hd2, rowID, 6, 1, 3);
|
|
|
|
///========================== board settings
|
|
rowID ++;
|
|
cbIQDigi = new RComboBox(ICTab);
|
|
for( int i = 0; i < nDigi; i++) cbIQDigi->addItem("Digi-" + QString::number(digi[i]->GetSerialNumber()), i);
|
|
inquiryLayout->addWidget(cbIQDigi, rowID, 0);
|
|
connect( cbIQDigi, &RComboBox::currentIndexChanged, this, [=](int index){
|
|
enableSignalSlot = false;
|
|
ID = index;
|
|
cbIQCh->clear();
|
|
for( int i = 0; i < digi[index]->GetNChannels() ; i++ ) cbIQCh->addItem( "Ch-" + QString::number(i), i);
|
|
|
|
cbBdSettings->clear();
|
|
cbChSettings->clear();
|
|
if( digi[ID]->GetFPGAType() == DPPType::PHA ){
|
|
for( int i = 0; i < (int) PHA::DIG::AllSettings.size(); i++ ){
|
|
cbBdSettings->addItem( QString::fromStdString( PHA::DIG::AllSettings[i].GetPara() ), i);
|
|
}
|
|
for( int i = 0; i < (int) PHA::CH::AllSettings.size(); i++ ){
|
|
cbChSettings->addItem( QString::fromStdString( PHA::CH::AllSettings[i].GetPara() ), i);
|
|
}
|
|
}
|
|
if( digi[ID]->GetFPGAType() == DPPType::PSD ){
|
|
for( int i = 0; i < (int) PSD::DIG::AllSettings.size(); i++ ){
|
|
cbBdSettings->addItem( QString::fromStdString( PSD::DIG::AllSettings[i].GetPara() ), i);
|
|
}
|
|
for( int i = 0; i < (int) PSD::CH::AllSettings.size(); i++ ){
|
|
cbChSettings->addItem( QString::fromStdString( PSD::CH::AllSettings[i].GetPara() ), i);
|
|
}
|
|
}
|
|
|
|
|
|
|
|
enableSignalSlot = true;
|
|
});
|
|
|
|
cbBdSettings = new RComboBox(ICTab);
|
|
if( digi[0]->GetFPGAType() == DPPType::PHA ){
|
|
for( int i = 0; i < (int) PHA::DIG::AllSettings.size(); i++ ){
|
|
cbBdSettings->addItem( QString::fromStdString( PHA::DIG::AllSettings[i].GetPara() ), i);
|
|
}
|
|
}
|
|
if( digi[ID]->GetFPGAType() == DPPType::PSD ){
|
|
for( int i = 0; i < (int) PSD::DIG::AllSettings.size(); i++ ){
|
|
cbBdSettings->addItem( QString::fromStdString( PSD::DIG::AllSettings[i].GetPara() ), i);
|
|
}
|
|
}
|
|
|
|
inquiryLayout->addWidget(cbBdSettings, rowID, 1);
|
|
connect(cbBdSettings, &RComboBox::currentIndexChanged, this, &DigiSettingsPanel::ReadBoardSetting);
|
|
|
|
leBdSettingsType = new QLineEdit("Read Only",ICTab);
|
|
leBdSettingsType->setAlignment(Qt::AlignHCenter);
|
|
leBdSettingsType->setFixedWidth(150);
|
|
leBdSettingsType->setReadOnly(true);
|
|
inquiryLayout->addWidget(leBdSettingsType, rowID, 2);
|
|
|
|
leBdSettingsRead = new QLineEdit(ICTab);
|
|
leBdSettingsRead->setAlignment(Qt::AlignRight);
|
|
leBdSettingsRead->setFixedWidth(250);
|
|
leBdSettingsRead->setReadOnly(true);
|
|
inquiryLayout->addWidget(leBdSettingsRead, rowID, 3);
|
|
|
|
leBdSettingsUnit = new QLineEdit("", ICTab);
|
|
leBdSettingsUnit->setAlignment(Qt::AlignHCenter);
|
|
leBdSettingsUnit->setFixedWidth(50);
|
|
leBdSettingsUnit->setReadOnly(true);
|
|
inquiryLayout->addWidget(leBdSettingsUnit, rowID, 4);
|
|
|
|
QPushButton * bnRead = new QPushButton("Read", ICTab);
|
|
inquiryLayout->addWidget(bnRead, rowID, 5, 2, 1);
|
|
connect(bnRead, &QPushButton::clicked, this, [=](){ ReadBoardSetting(cbBdSettings->currentIndex()); ReadChannelSetting(cbChSettings->currentIndex()); });
|
|
|
|
cbBdAns = new RComboBox(ICTab);
|
|
cbBdAns->setFixedWidth(200);
|
|
inquiryLayout->addWidget(cbBdAns, rowID, 6);
|
|
connect(cbBdAns, &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
std::string value = cbBdAns->currentData().toString().toStdString();
|
|
leBdSettingsWrite->setText(QString::fromStdString(value));
|
|
leBdSettingsWrite->setStyleSheet("");
|
|
|
|
Reg para = PHA::DIG::AllSettings[cbBdSettings->currentIndex()];
|
|
ID = cbIQDigi->currentIndex();
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += " = " + cbBdAns->currentData().toString();
|
|
if( digi[ID]->WriteValue(para, value) ){
|
|
leBdSettingsRead->setText( QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para)));
|
|
SendLogMsg(msg + "|OK.");
|
|
cbBdAns->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
leBdSettingsRead->setText("fail write value");
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbBdAns->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
sbBdSettingsWrite = new RSpinBox(ICTab);
|
|
sbBdSettingsWrite->setFixedWidth(200);
|
|
inquiryLayout->addWidget(sbBdSettingsWrite, rowID, 7);
|
|
connect(sbBdSettingsWrite, &RSpinBox::valueChanged, this, [=](){if( enableSignalSlot ) sbBdSettingsWrite->setStyleSheet("color: green;");});
|
|
connect(sbBdSettingsWrite, &RSpinBox::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
if( sbBdSettingsWrite->decimals() == 0 && sbBdSettingsWrite->singleStep() != 1) {
|
|
double step = sbBdSettingsWrite->singleStep();
|
|
double value = sbBdSettingsWrite->value();
|
|
sbBdSettingsWrite->setValue( (std::round(value/step) * step) );
|
|
}
|
|
|
|
Reg para = PHA::DIG::AllSettings[cbBdSettings->currentIndex()];
|
|
ID = cbIQDigi->currentIndex();
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += " = " + QString::number(sbBdSettingsWrite->value());
|
|
if( digi[ID]->WriteValue(para, std::to_string(sbBdSettingsWrite->value()))){
|
|
leBdSettingsRead->setText( QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para)));
|
|
SendLogMsg(msg + "|OK.");
|
|
sbBdSettingsWrite->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
leBdSettingsRead->setText("fail write value");
|
|
SendLogMsg(msg + "|Fail.");
|
|
sbBdSettingsWrite->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
leBdSettingsWrite = new QLineEdit(ICTab);
|
|
leBdSettingsWrite->setAlignment(Qt::AlignRight);
|
|
leBdSettingsWrite->setFixedWidth(200);
|
|
inquiryLayout->addWidget(leBdSettingsWrite, rowID, 8);
|
|
connect(leBdSettingsWrite, &QLineEdit::textChanged, this, [=](){if( enableSignalSlot )leBdSettingsWrite->setStyleSheet("color: blue;");});
|
|
connect(leBdSettingsWrite, &QLineEdit::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
std::string value = leBdSettingsWrite->text().toStdString();
|
|
Reg para = PHA::DIG::AllSettings[cbBdSettings->currentIndex()];
|
|
ID = cbIQDigi->currentIndex();
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += " = " + QString::number(sbBdSettingsWrite->value());
|
|
if( digi[ID]->WriteValue(para, value)){
|
|
leBdSettingsRead->setText( QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para)));
|
|
SendLogMsg(msg + "|OK.");
|
|
sbBdSettingsWrite->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
leBdSettingsRead->setText("fail write value");
|
|
SendLogMsg(msg + "|Fail.");
|
|
sbBdSettingsWrite->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
|
|
///========================== Channels settings
|
|
rowID ++;
|
|
cbIQCh = new RComboBox(ICTab);
|
|
cbIQCh->clear();
|
|
for( int i = 0; i < digi[0]->GetNChannels() ; i++) cbIQCh->addItem("Ch-" + QString::number(i), i);
|
|
inquiryLayout->addWidget(cbIQCh, rowID, 0);
|
|
connect(cbIQCh, &RComboBox::currentIndexChanged, this, [=](){ ReadChannelSetting(cbChSettings->currentIndex()); });
|
|
|
|
cbChSettings = new RComboBox(ICTab);
|
|
if( digi[0]->GetFPGAType() == DPPType::PHA){
|
|
for( int i = 0; i < (int) PHA::CH::AllSettings.size(); i++ ){
|
|
cbChSettings->addItem( QString::fromStdString( PHA::CH::AllSettings[i].GetPara() ), i);
|
|
}
|
|
}
|
|
if( digi[0]->GetFPGAType() == DPPType::PSD){
|
|
for( int i = 0; i < (int) PSD::CH::AllSettings.size(); i++ ){
|
|
cbChSettings->addItem( QString::fromStdString( PSD::CH::AllSettings[i].GetPara() ), i);
|
|
}
|
|
}
|
|
inquiryLayout->addWidget(cbChSettings, rowID, 1);
|
|
connect(cbChSettings, &RComboBox::currentIndexChanged, this, &DigiSettingsPanel::ReadChannelSetting);
|
|
|
|
leChSettingsType = new QLineEdit("Read Only", ICTab);
|
|
leChSettingsType->setAlignment(Qt::AlignHCenter);
|
|
leChSettingsType->setFixedWidth(150);
|
|
leChSettingsType->setReadOnly(true);
|
|
inquiryLayout->addWidget(leChSettingsType, rowID, 2);
|
|
|
|
leChSettingsRead = new QLineEdit(ICTab);
|
|
leChSettingsRead->setAlignment(Qt::AlignRight);
|
|
leChSettingsRead->setFixedWidth(250);
|
|
leChSettingsRead->setReadOnly(true);
|
|
inquiryLayout->addWidget(leChSettingsRead, rowID, 3);
|
|
|
|
leChSettingsUnit = new QLineEdit(ICTab);
|
|
leChSettingsUnit->setAlignment(Qt::AlignHCenter);
|
|
leChSettingsUnit->setFixedWidth(50);
|
|
leChSettingsUnit->setReadOnly(true);
|
|
inquiryLayout->addWidget(leChSettingsUnit, rowID, 4);
|
|
|
|
cbChSettingsWrite = new RComboBox(ICTab);
|
|
cbChSettingsWrite->setFixedWidth(200);
|
|
inquiryLayout->addWidget(cbChSettingsWrite, rowID, 6);
|
|
connect(cbChSettingsWrite, &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
std::string value = cbChSettingsWrite->currentData().toString().toStdString();
|
|
leChSettingsWrite->setText(QString::fromStdString(value));
|
|
leChSettingsWrite->setStyleSheet("");
|
|
|
|
Reg para = PHA::CH::AllSettings[cbChSettings->currentIndex()];
|
|
ID = cbIQDigi->currentIndex();
|
|
int ch_index = cbIQCh->currentIndex();
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += ",CH:" + QString::number(ch_index);
|
|
msg += " = " + cbChSettingsWrite->currentData().toString();
|
|
if( digi[ID]->WriteValue(para, value, ch_index) ){
|
|
leChSettingsRead->setText( QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para)));
|
|
SendLogMsg(msg + "|OK.");
|
|
cbChSettingsWrite->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
leChSettingsRead->setText("fail write value");
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbChSettingsWrite->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
sbChSettingsWrite = new RSpinBox(ICTab);
|
|
sbChSettingsWrite->setFixedWidth(200);
|
|
inquiryLayout->addWidget(sbChSettingsWrite, rowID, 7);
|
|
connect(sbChSettingsWrite, &RSpinBox::valueChanged, this, [=](){ if( enableSignalSlot ) sbChSettingsWrite->setStyleSheet("color: green;");});
|
|
connect(sbChSettingsWrite, &RSpinBox::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
if( sbChSettingsWrite->decimals() == 0 && sbChSettingsWrite->singleStep() != 1) {
|
|
double step = sbChSettingsWrite->singleStep();
|
|
double value = sbChSettingsWrite->value();
|
|
sbChSettingsWrite->setValue( (std::round(value/step) * step) );
|
|
}
|
|
|
|
Reg para = PHA::CH::AllSettings[cbChSettings->currentIndex()];
|
|
ID = cbIQDigi->currentIndex();
|
|
int ch_index = cbIQCh->currentIndex();
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += ",CH:" + QString::number(ch_index);
|
|
msg += " = " + QString::number(sbChSettingsWrite->value());
|
|
if( digi[ID]->WriteValue(para, std::to_string(sbChSettingsWrite->value()), ch_index)){
|
|
leChSettingsRead->setText( QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para)));
|
|
SendLogMsg(msg + "|OK.");
|
|
sbChSettingsWrite->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
leChSettingsRead->setText("fail write value");
|
|
SendLogMsg(msg + "|Fail.");
|
|
sbChSettingsWrite->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
leChSettingsWrite = new QLineEdit(ICTab);
|
|
leChSettingsWrite->setFixedWidth(200);
|
|
inquiryLayout->addWidget(leChSettingsWrite, rowID, 8);
|
|
connect(leChSettingsWrite, &QLineEdit::textChanged, this, [=](){if( enableSignalSlot ) leChSettingsWrite->setStyleSheet("color: green;");});
|
|
connect(leChSettingsWrite, &QLineEdit::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
std::string value = leChSettingsWrite->text().toStdString();
|
|
Reg para = PHA::CH::AllSettings[cbChSettings->currentIndex()];
|
|
ID = cbIQDigi->currentIndex();
|
|
int ch_index = cbIQCh->currentIndex();
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
msg += " = " + QString::number(sbChSettingsWrite->value());
|
|
if( digi[ID]->WriteValue(para, value, ch_index)){
|
|
leChSettingsRead->setText( QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para)));
|
|
SendLogMsg(msg + "|OK.");
|
|
sbChSettingsWrite->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
leChSettingsRead->setText("fail write value");
|
|
SendLogMsg(msg + "|Fail.");
|
|
sbChSettingsWrite->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
for( int i = 0 ; i < inquiryLayout->count(); i++) inquiryLayout->setColumnStretch(i, 1);
|
|
|
|
}
|
|
|
|
{//@============== Copy setting
|
|
icBox2 = new QGroupBox("Copy Settings", ICTab);
|
|
layout1->addWidget(icBox2);
|
|
|
|
QGridLayout * cpLayout = new QGridLayout(icBox2);
|
|
cpLayout->setAlignment(Qt::AlignCenter | Qt::AlignLeft);
|
|
|
|
///================
|
|
QGroupBox * icBox2a = new QGroupBox("Copy From", icBox2);
|
|
cpLayout->addWidget(icBox2a, 0, 0, 5, 1);
|
|
|
|
QGridLayout * lo1 = new QGridLayout(icBox2a);
|
|
|
|
cbCopyDigiFrom = new RComboBox(ICTab);
|
|
for( int i = 0; i < nDigi; i++) cbCopyDigiFrom->addItem("Digi-" + QString::number(digi[i]->GetSerialNumber()), i);
|
|
lo1->addWidget(cbCopyDigiFrom, 0, 0, 1, 8);
|
|
connect(cbCopyDigiFrom, &RComboBox::currentIndexChanged, this, [=](int index){
|
|
|
|
CheckRadioAndCheckedButtons();
|
|
|
|
if( !CheckDigitizersCanCopy() ) {
|
|
pbCopyChannel->setEnabled(false);
|
|
return;
|
|
}
|
|
|
|
if( index == cbCopyDigiTo->currentIndex() ){
|
|
pbCopyBoard->setEnabled(false);
|
|
pbCopyDigi->setEnabled(false);
|
|
}else{
|
|
pbCopyBoard->setEnabled(true);
|
|
pbCopyDigi->setEnabled(true);
|
|
}
|
|
});
|
|
|
|
int rowID = 0;
|
|
for( int i = 0; i < digi[0]->GetNChannels(); i++) {
|
|
if( i % 8 == 0) rowID ++;
|
|
rbCopyChFrom[i] = new QRadioButton("Ch-" + QString::number(i), ICTab);
|
|
lo1->addWidget(rbCopyChFrom[i], rowID, i%8);
|
|
connect(rbCopyChFrom[i], &QRadioButton::clicked, this, &DigiSettingsPanel::CheckRadioAndCheckedButtons);
|
|
}
|
|
|
|
///================
|
|
pbCopyChannel = new QPushButton("Copy Ch. Setting", ICTab);
|
|
pbCopyChannel->setFixedSize(200, 50);
|
|
cpLayout->addWidget(pbCopyChannel, 1, 1);
|
|
pbCopyChannel->setEnabled(false);
|
|
connect(pbCopyChannel, &QPushButton::clicked, this, [=](){
|
|
|
|
int chFromIndex = -1;
|
|
for( int i = 0 ; i < MaxNumberOfChannel ; i++){
|
|
if( rbCopyChFrom[i]->isChecked() ){
|
|
chFromIndex = i;
|
|
break;
|
|
}
|
|
}
|
|
if( chFromIndex < 0 ) return;
|
|
|
|
for( int i = 0; i < MaxNumberOfChannel; i++){
|
|
if( chkChTo[i]->isChecked() ) CopyChannelSettings(cbCopyDigiFrom->currentIndex(), chFromIndex, cbCopyDigiTo->currentIndex(), i );
|
|
}
|
|
SendLogMsg("------ done");
|
|
});
|
|
|
|
pbCopyBoard = new QPushButton("Copy Board Settings", ICTab);
|
|
pbCopyBoard->setFixedSize(200, 50);
|
|
cpLayout->addWidget(pbCopyBoard, 2, 1);
|
|
pbCopyBoard->setEnabled(false);
|
|
connect(pbCopyBoard, &QPushButton::clicked, this, &DigiSettingsPanel::CopyBoardSettings);
|
|
|
|
pbCopyDigi = new QPushButton("Copy Digitizer", ICTab);
|
|
pbCopyDigi->setFixedSize(200, 50);
|
|
cpLayout->addWidget(pbCopyDigi, 3, 1);
|
|
pbCopyDigi->setEnabled(false);
|
|
connect(pbCopyDigi, &QPushButton::clicked, this, &DigiSettingsPanel::CopyWholeDigitizer);
|
|
|
|
///================
|
|
QGroupBox * icBox2b = new QGroupBox("Copy To", icBox2);
|
|
cpLayout->addWidget(icBox2b, 0, 2, 5, 1);
|
|
|
|
QGridLayout * lo2 = new QGridLayout(icBox2b);
|
|
|
|
cbCopyDigiTo = new RComboBox(ICTab);
|
|
for( int i = 0; i < nDigi; i++) cbCopyDigiTo->addItem("Digi-" + QString::number(digi[i]->GetSerialNumber()), i);
|
|
lo2->addWidget(cbCopyDigiTo, 0, 0, 1, 8);
|
|
connect(cbCopyDigiTo, &RComboBox::currentIndexChanged, this, [=](int index){
|
|
CheckRadioAndCheckedButtons();
|
|
|
|
if( !CheckDigitizersCanCopy() ) {
|
|
pbCopyChannel->setEnabled(false);
|
|
return;
|
|
}
|
|
|
|
if( index == cbCopyDigiFrom->currentIndex() ){
|
|
pbCopyBoard->setEnabled(false);
|
|
pbCopyDigi->setEnabled(false);
|
|
}else{
|
|
pbCopyBoard->setEnabled(true);
|
|
pbCopyDigi->setEnabled(true);
|
|
}
|
|
});
|
|
|
|
rowID = 0;
|
|
|
|
for( int i = 0; i < digi[0]->GetNChannels(); i++) {
|
|
if( i % 8 == 0) rowID ++;
|
|
chkChTo[i] = new QCheckBox("ch-" + QString::number(i), ICTab);
|
|
lo2->addWidget(chkChTo[i], rowID, i%8);
|
|
connect(chkChTo[i], &QCheckBox::clicked, this, &DigiSettingsPanel::CheckRadioAndCheckedButtons);
|
|
}
|
|
|
|
cpLayout->setColumnStretch(0, 4);
|
|
cpLayout->setColumnStretch(1, 1);
|
|
cpLayout->setColumnStretch(2, 4);
|
|
}
|
|
}
|
|
|
|
connect(tabWidget, &QTabWidget::currentChanged, this, [=](int index){
|
|
if( index < nDigi) {
|
|
ID = index;
|
|
UpdatePanelFromMemory();
|
|
}else{
|
|
ID = 0;
|
|
}
|
|
});
|
|
|
|
for( ID = 0; ID < nDigi; ID ++) EnableControl();
|
|
|
|
ID = 0;
|
|
|
|
cbBdSettings->setCurrentText("ModelName");
|
|
cbChSettings->setCurrentIndex(10);
|
|
|
|
show();
|
|
|
|
enableSignalSlot = true;
|
|
}
|
|
|
|
DigiSettingsPanel::~DigiSettingsPanel(){
|
|
|
|
//printf("%s\n", __func__);
|
|
|
|
}
|
|
|
|
|
|
void DigiSettingsPanel::SetupPHAChannels(unsigned short digiID){
|
|
|
|
//@.......... All Settings tab
|
|
QWidget * tab_All = new QWidget(digiTab[digiID]);
|
|
//tab_All->setStyleSheet("background-color: #EEEEEE");
|
|
chTabWidget[digiID]->addTab(tab_All, "All/Single Ch.");
|
|
|
|
QGridLayout * allLayout = new QGridLayout(tab_All);
|
|
allLayout->setAlignment(Qt::AlignTop);
|
|
|
|
unsigned short ch = digi[digiID]->GetNChannels();
|
|
|
|
{//*--------- Group 0
|
|
box0[digiID] = new QGroupBox("Channel Selection", digiTab[digiID]);
|
|
allLayout->addWidget(box0[digiID]);
|
|
QGridLayout * layout0 = new QGridLayout(box0[digiID]);
|
|
layout0->setAlignment(Qt::AlignLeft);
|
|
|
|
QLabel * lbCh = new QLabel("Channel :", digiTab[digiID]);
|
|
lbCh->setAlignment(Qt::AlignCenter | Qt::AlignRight);
|
|
layout0->addWidget(lbCh, 0, 0);
|
|
|
|
cbChPick[digiID] = new RComboBox(digiTab[digiID]);
|
|
cbChPick[digiID]->addItem("All", -1);
|
|
for( int i = 0; i < ch; i++) cbChPick[digiID]->addItem("Ch-" + QString::number(i), i);
|
|
layout0->addWidget(cbChPick[digiID], 0, 1);
|
|
connect(cbChPick[digiID], &RComboBox::currentIndexChanged, this, [=](){
|
|
int index = cbChPick[ID]->currentData().toInt();
|
|
if(index == -1) {
|
|
UpdatePanelFromMemory();
|
|
return;
|
|
}else{
|
|
enableSignalSlot = false;
|
|
unsigned short ch = digi[digiID]->GetNChannels();
|
|
//printf("index = %d, ch = %d\n", index, ch);
|
|
FillComboBoxValueFromMemory(cbbOnOff[ID][ch], PHA::CH::ChannelEnable, index);
|
|
FillSpinBoxValueFromMemory(spbDCOffset[ID][ch], PHA::CH::DC_Offset, index);
|
|
FillSpinBoxValueFromMemory(spbThreshold[ID][ch], PHA::CH::TriggerThreshold, index);
|
|
FillComboBoxValueFromMemory(cbbParity[ID][ch], PHA::CH::Polarity, index);
|
|
FillSpinBoxValueFromMemory(spbRecordLength[ID][ch], PHA::CH::RecordLength, index);
|
|
FillSpinBoxValueFromMemory(spbPreTrigger[ID][ch], PHA::CH::PreTrigger, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbWaveSource[ID][ch], PHA::CH::WaveDataSource, index);
|
|
FillComboBoxValueFromMemory(cbbWaveRes[ID][ch], PHA::CH::WaveResolution, index);
|
|
FillComboBoxValueFromMemory(cbbWaveSave[ID][ch], PHA::CH::WaveSaving, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbAnaProbe0[ID][ch], PHA::CH::WaveAnalogProbe0, index);
|
|
FillComboBoxValueFromMemory(cbbAnaProbe1[ID][ch], PHA::CH::WaveAnalogProbe1, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe0[ID][ch], PHA::CH::WaveDigitalProbe0, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe1[ID][ch], PHA::CH::WaveDigitalProbe1, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe2[ID][ch], PHA::CH::WaveDigitalProbe2, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe3[ID][ch], PHA::CH::WaveDigitalProbe3, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbEventSelector[ID][ch], PHA::CH::EventSelector, index);
|
|
FillComboBoxValueFromMemory(cbbWaveSelector[ID][ch], PHA::CH::WaveSelector, index);
|
|
FillSpinBoxValueFromMemory(spbEnergySkimLow[ID][ch], PHA::CH::EnergySkimLowDiscriminator, index);
|
|
FillSpinBoxValueFromMemory(spbEnergySkimHigh[ID][ch], PHA::CH::EnergySkimHighDiscriminator, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbEvtTrigger[ID][ch], PHA::CH::EventTriggerSource, index);
|
|
FillComboBoxValueFromMemory(cbbWaveTrigger[ID][ch], PHA::CH::WaveTriggerSource, index);
|
|
FillComboBoxValueFromMemory(cbbChVetoSrc[ID][ch], PHA::CH::ChannelVetoSource, index);
|
|
FillComboBoxValueFromMemory(cbbCoinMask[ID][ch], PHA::CH::CoincidenceMask, index);
|
|
FillComboBoxValueFromMemory(cbbAntiCoinMask[ID][ch], PHA::CH::AntiCoincidenceMask, index);
|
|
FillSpinBoxValueFromMemory(spbCoinLength[ID][ch], PHA::CH::CoincidenceLength, index);
|
|
FillSpinBoxValueFromMemory(spbADCVetoWidth[ID][ch], PHA::CH::ADCVetoWidth, index);
|
|
|
|
unsigned long mask = Utility::TenBase(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, cbChPick[ID]->currentData().toInt()));
|
|
leTriggerMask[ID][ch]->setText("0x" + QString::number(mask, 16).toUpper());
|
|
|
|
//-------- PHA
|
|
FillSpinBoxValueFromMemory(spbInputRiseTime[ID][ch], PHA::CH::TimeFilterRiseTime, index);
|
|
FillSpinBoxValueFromMemory(spbTriggerGuard[ID][ch], PHA::CH::TimeFilterRetriggerGuard, index);
|
|
FillComboBoxValueFromMemory(cbbLowFilter[ID][ch], PHA::CH::EnergyFilterLowFreqFilter, index);
|
|
|
|
FillSpinBoxValueFromMemory(spbTrapRiseTime[ID][ch], PHA::CH::EnergyFilterRiseTime, index);
|
|
FillSpinBoxValueFromMemory(spbTrapFlatTop[ID][ch], PHA::CH::EnergyFilterFlatTop, index);
|
|
FillSpinBoxValueFromMemory(spbTrapPoleZero[ID][ch], PHA::CH::EnergyFilterPoleZero, index);
|
|
|
|
FillSpinBoxValueFromMemory(spbPeaking[ID][ch], PHA::CH::EnergyFilterPeakingPosition, index);
|
|
FillSpinBoxValueFromMemory(spbBaselineGuard[ID][ch], PHA::CH::EnergyFilterBaselineGuard, index);
|
|
FillSpinBoxValueFromMemory(spbPileupGuard[ID][ch], PHA::CH::EnergyFilterPileUpGuard, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbBaselineAvg[ID][ch], PHA::CH::EnergyFilterBaselineAvg, index);
|
|
FillComboBoxValueFromMemory(cbbPeakingAvg[ID][ch], PHA::CH::EnergyFilterPeakingAvg, index);
|
|
FillSpinBoxValueFromMemory(spbFineGain[ID][ch], PHA::CH::EnergyFilterFineGain, index);
|
|
|
|
enableSignalSlot = true;
|
|
}
|
|
});
|
|
|
|
}
|
|
|
|
int rowID = 0;
|
|
{//*--------- Group 1
|
|
box1[digiID] = new QGroupBox("Input Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box1[digiID]);
|
|
QGridLayout * layout1 = new QGridLayout(box1[digiID]);
|
|
|
|
rowID = 0;
|
|
SetupComboBox(cbbOnOff[digiID][ch], PHA::CH::ChannelEnable, -1, true, "On/Off", layout1, rowID, 0);
|
|
SetupComboBox(cbbWaveSource[digiID][ch], PHA::CH::WaveDataSource, -1, true, "Wave Data Source", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupComboBox(cbbWaveRes[digiID][ch], PHA::CH::WaveResolution, -1, true, "Wave Resol.", layout1, rowID, 0);
|
|
SetupComboBox(cbbWaveSave[digiID][ch], PHA::CH::WaveSaving, -1, true, "Wave Save", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbDCOffset[digiID][ch], PHA::CH::DC_Offset, -1, true, "DC Offset [%]", layout1, rowID, 0);
|
|
SetupSpinBox(spbThreshold[digiID][ch], PHA::CH::TriggerThreshold, -1, true, "Threshold [LSB]", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbRecordLength[digiID][ch], PHA::CH::RecordLength, -1, true, "Record Length [ns]", layout1, rowID, 0);
|
|
SetupSpinBox(spbPreTrigger[digiID][ch], PHA::CH::PreTrigger, -1, true, "Pre Trigger [ns]", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupComboBox(cbbParity[digiID][ch], PHA::CH::Polarity, -1, true, "Parity", layout1, rowID, 0);
|
|
SetupComboBox(cbbLowFilter[digiID][ch], PHA::CH::EnergyFilterLowFreqFilter, -1, true, "Low Freq. Filter", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbInputRiseTime[digiID][ch], PHA::CH::TimeFilterRiseTime, -1, true, "Input Rise Time [ns]", layout1, rowID, 0);
|
|
SetupSpinBox(spbTriggerGuard[digiID][ch], PHA::CH::TimeFilterRetriggerGuard, -1, true, "Trigger Guard [ns]", layout1, rowID, 2);
|
|
|
|
}
|
|
|
|
{//*--------- Group 2
|
|
box3[digiID] = new QGroupBox("Trap. Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box3[digiID]);
|
|
QGridLayout * layout3 = new QGridLayout(box3[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0;
|
|
SetupSpinBox(spbTrapRiseTime[digiID][ch], PHA::CH::EnergyFilterRiseTime, -1, true, "Trap. Rise Time [ns]", layout3, rowID, 0);
|
|
SetupSpinBox(spbTrapFlatTop[digiID][ch], PHA::CH::EnergyFilterFlatTop, -1, true, "Trap. Flat Top [ns]", layout3, rowID, 2);
|
|
SetupSpinBox(spbTrapPoleZero[digiID][ch], PHA::CH::EnergyFilterPoleZero, -1, true, "Trap. Pole Zero [ns]", layout3, rowID, 4);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupSpinBox(spbPeaking[digiID][ch], PHA::CH::EnergyFilterPeakingPosition, -1, true, "Peaking [%]", layout3, rowID, 0);
|
|
SetupSpinBox(spbBaselineGuard[digiID][ch], PHA::CH::EnergyFilterBaselineGuard, -1, true, "Baseline Guard [ns]", layout3, rowID, 2);
|
|
SetupSpinBox(spbPileupGuard[digiID][ch], PHA::CH::EnergyFilterPileUpGuard, -1, true, "Pile-up Guard [ns]", layout3, rowID, 4);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbPeakingAvg[digiID][ch], PHA::CH::EnergyFilterPeakingAvg, -1, true, "Peak Avg", layout3, rowID, 0);
|
|
SetupComboBox(cbbBaselineAvg[digiID][ch], PHA::CH::EnergyFilterBaselineAvg, -1, true, "Baseline Avg", layout3, rowID, 2);
|
|
SetupSpinBox(spbFineGain[digiID][ch], PHA::CH::EnergyFilterFineGain, -1, true, "Fine Gain", layout3, rowID, 4);
|
|
|
|
}
|
|
|
|
{//*--------- Group 3
|
|
box4[digiID] = new QGroupBox("Probe Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box4[digiID]);
|
|
QGridLayout * layout4 = new QGridLayout(box4[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0;
|
|
SetupComboBox(cbbAnaProbe0[digiID][ch], PHA::CH::WaveAnalogProbe0, -1, true, "Analog Prob. 0", layout4, rowID, 0, 1, 2);
|
|
SetupComboBox(cbbAnaProbe1[digiID][ch], PHA::CH::WaveAnalogProbe1, -1, true, "Analog Prob. 1", layout4, rowID, 3, 1, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbDigProbe0[digiID][ch], PHA::CH::WaveDigitalProbe0, -1, true, "Digitial Prob. 0", layout4, rowID, 0, 1, 2);
|
|
SetupComboBox(cbbDigProbe1[digiID][ch], PHA::CH::WaveDigitalProbe1, -1, true, "Digitial Prob. 1", layout4, rowID, 3, 1, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbDigProbe2[digiID][ch], PHA::CH::WaveDigitalProbe2, -1, true, "Digitial Prob. 2", layout4, rowID, 0, 1, 2);
|
|
SetupComboBox(cbbDigProbe3[digiID][ch], PHA::CH::WaveDigitalProbe3, -1, true, "Digitial Prob. 3", layout4, rowID, 3, 1, 2);
|
|
|
|
}
|
|
|
|
{//*--------- Group 4
|
|
box5[digiID] = new QGroupBox("Trigger Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box5[digiID]);
|
|
QGridLayout * layout5 = new QGridLayout(box5[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0;
|
|
SetupComboBox(cbbEvtTrigger[digiID][ch], PHA::CH::EventTriggerSource, -1, true, "Event Trig. Source", layout5, rowID, 0);
|
|
SetupComboBox(cbbWaveTrigger[digiID][ch], PHA::CH::WaveTriggerSource, -1, true, "Wave Trig. Source", layout5, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbChVetoSrc[digiID][ch], PHA::CH::ChannelVetoSource, -1, true, "Veto Source", layout5, rowID, 0);
|
|
|
|
QLabel * lbTrgMsk = new QLabel("Trigger Mask");
|
|
lbTrgMsk->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
layout5->addWidget(lbTrgMsk, rowID, 2);
|
|
leTriggerMask[digiID][ch] = new QLineEdit(this);
|
|
leTriggerMask[digiID][ch]->setToolTip("Both Hex or Dec is OK.");
|
|
layout5->addWidget(leTriggerMask[digiID][ch], rowID, 3);
|
|
|
|
connect(leTriggerMask[digiID][ch], &QLineEdit::textChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
leTriggerMask[digiID][ch]->setStyleSheet("color:blue;");
|
|
});
|
|
|
|
connect(leTriggerMask[digiID][ch], &QLineEdit::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
int index = cbChPick[ID]->currentData().toInt();
|
|
|
|
QString SixteenBaseValue = "0x" + QString::number(Utility::TenBase(leTriggerMask[ID][ch]->text().toStdString()), 16).toUpper();
|
|
leTriggerMask[ID][ch]->setText(SixteenBaseValue);
|
|
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::CH::ChannelsTriggerMask.GetPara()) ;
|
|
msg += ",CH:" + (index == -1 ? "All" : QString::number(index));
|
|
msg += " = " + SixteenBaseValue;
|
|
|
|
if( digi[ID]->WriteValue(PHA::CH::ChannelsTriggerMask, SixteenBaseValue.toStdString(), index)){
|
|
SendLogMsg(msg + "|OK.");
|
|
leTriggerMask[ID][ch]->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
leTriggerMask[ID][ch]->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbCoinMask[digiID][ch], PHA::CH::CoincidenceMask, -1, true, "Coin. Mask", layout5, rowID, 0);
|
|
SetupComboBox(cbbAntiCoinMask[digiID][ch], PHA::CH::AntiCoincidenceMask, -1, true, "Anti-Coin. Mask", layout5, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupSpinBox(spbCoinLength[digiID][ch], PHA::CH::CoincidenceLength, -1, true, "Coin. Length [ns]", layout5, rowID, 0);
|
|
SetupSpinBox(spbADCVetoWidth[digiID][ch], PHA::CH::ADCVetoWidth, -1, true, "ADC Veto Length [ns]", layout5, rowID, 2);
|
|
|
|
for( int i = 0; i < layout5->columnCount(); i++) layout5->setColumnStretch(i, 1);
|
|
|
|
}
|
|
|
|
{//*--------- Group 5
|
|
box6[digiID] = new QGroupBox("Other Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box6[digiID]);
|
|
QGridLayout * layout6 = new QGridLayout(box6[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0 ;
|
|
SetupComboBox(cbbEventSelector[digiID][ch], PHA::CH::EventSelector, -1, true, "Event Selector", layout6, rowID, 0);
|
|
SetupComboBox(cbbWaveSelector[digiID][ch], PHA::CH::WaveSelector, -1, true, "Wave Selector", layout6, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupSpinBox(spbEnergySkimLow[digiID][ch], PHA::CH::EnergySkimLowDiscriminator, -1, true, "Energy Skim Low", layout6, rowID, 0);
|
|
SetupSpinBox(spbEnergySkimHigh[digiID][ch], PHA::CH::EnergySkimHighDiscriminator, -1, true, "Energy Skim High", layout6, rowID, 2);
|
|
}
|
|
|
|
|
|
|
|
{//@============== input tab
|
|
inputTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(inputTab[digiID], "Input");
|
|
|
|
SetupComboBoxTab(cbbOnOff, PHA::CH::ChannelEnable, "On/Off", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveSource, PHA::CH::WaveDataSource, "Wave Data Dource", inputTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbWaveRes, PHA::CH::WaveResolution, "Wave Resol.", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveSave, PHA::CH::WaveSaving, "Wave Save", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbDCOffset, PHA::CH::DC_Offset, "DC Offset [%]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbThreshold, PHA::CH::TriggerThreshold, "Threshold [LSB]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbRecordLength, PHA::CH::RecordLength, "Record Length [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbPreTrigger, PHA::CH::PreTrigger, "PreTrigger [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbParity, PHA::CH::Polarity, "Parity", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
SetupSpinBoxTab(spbInputRiseTime, PHA::CH::TimeFilterRiseTime, "Input Rise Time [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbTriggerGuard, PHA::CH::TimeFilterRetriggerGuard, "Trigger Guard [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbLowFilter, PHA::CH::EnergyFilterLowFreqFilter, "Low Freq. Filter", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
for( int ch = 0; ch < digi[digiID]->GetNChannels(); ch++){
|
|
//Set color of some combox
|
|
cbbOnOff[digiID][ch]->setItemData(1, QBrush(orangeColor), Qt::ForegroundRole);
|
|
connect(cbbOnOff[digiID][ch], &RComboBox::currentIndexChanged, this, [=](int index){ cbbOnOff[ID][ch]->setStyleSheet(index == 1 ? "color : orange;" : "");});
|
|
cbbParity[digiID][ch]->setItemData(1, QBrush(orangeColor), Qt::ForegroundRole);
|
|
connect(cbbParity[digiID][ch], &RComboBox::currentIndexChanged, this, [=](int index){ cbbParity[ID][ch]->setStyleSheet(index == 1 ? "color : orange;" : "");});
|
|
cbbLowFilter[digiID][ch]->setItemData(1, QBrush(orangeColor), Qt::ForegroundRole);
|
|
connect(cbbLowFilter[digiID][ch], &RComboBox::currentIndexChanged, this, [=](int index){ cbbLowFilter[ID][ch]->setStyleSheet(index == 1 ? "color : orange;": "");});
|
|
}
|
|
|
|
}
|
|
|
|
{//@============== Trap tab
|
|
trapTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(trapTab[digiID], "Trapezoid");
|
|
|
|
SetupSpinBoxTab(spbTrapRiseTime, PHA::CH::EnergyFilterRiseTime, "Trap. Rise Time [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbTrapFlatTop, PHA::CH::EnergyFilterFlatTop, "Trap. Flat Top [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbTrapPoleZero, PHA::CH::EnergyFilterPoleZero, "Trap. Pole Zero [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbPeaking, PHA::CH::EnergyFilterPeakingPosition, "Peaking [%]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbPeakingAvg, PHA::CH::EnergyFilterPeakingAvg, "Peak Avg.", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbBaselineAvg, PHA::CH::EnergyFilterBaselineAvg, "Baseline Avg.", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbFineGain, PHA::CH::EnergyFilterFineGain, "Fine Gain", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbBaselineGuard, PHA::CH::EnergyFilterBaselineGuard, "Baseline Guard [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbPileupGuard, PHA::CH::EnergyFilterPileUpGuard, "Pile-up Guard [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
}
|
|
|
|
{//@============== Probe tab
|
|
probeTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(probeTab[digiID], "Probe");
|
|
|
|
SetupComboBoxTab(cbbAnaProbe0, PHA::CH::WaveAnalogProbe0, "Analog Prob. 0", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbAnaProbe1, PHA::CH::WaveAnalogProbe1, "Analog Prob. 1", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe0, PHA::CH::WaveDigitalProbe0, "Digital Prob. 0", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe1, PHA::CH::WaveDigitalProbe1, "Digital Prob. 1", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe2, PHA::CH::WaveDigitalProbe2, "Digital Prob. 2", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe3, PHA::CH::WaveDigitalProbe3, "Digital Prob. 3", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
}
|
|
|
|
{//@============== Other tab
|
|
otherTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(otherTab[digiID], "Others");
|
|
|
|
SetupComboBoxTab(cbbEventSelector, PHA::CH::EventSelector, "Event Selector", otherTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveSelector, PHA::CH::WaveSelector, "Wave Selector", otherTab[digiID], digiID, digi[digiID]->GetNChannels(), 2 );
|
|
SetupSpinBoxTab(spbEnergySkimLow, PHA::CH::EnergySkimLowDiscriminator, "Energy Skim Low", otherTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbEnergySkimHigh, PHA::CH::EnergySkimHighDiscriminator, "Energy Skim High", otherTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
}
|
|
|
|
{//@============== Trigger tab
|
|
triggerTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(triggerTab[digiID], "Trigger");
|
|
|
|
SetupComboBoxTab(cbbEvtTrigger, PHA::CH::EventTriggerSource, "Event Trig. Source", triggerTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbWaveTrigger, PHA::CH::WaveTriggerSource, "Wave Trig. Source", triggerTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbChVetoSrc, PHA::CH::ChannelVetoSource, "Veto Source", triggerTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbCoinMask, PHA::CH::CoincidenceMask, "Coin. Mask", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbAntiCoinMask, PHA::CH::AntiCoincidenceMask, "Anti-Coin. Mask", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbCoinLength, PHA::CH::CoincidenceLength, "Coin. Length [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbADCVetoWidth, PHA::CH::ADCVetoWidth, "ADC Veto Length [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
}
|
|
|
|
for( int ch = 0; ch < digi[ID]->GetNChannels() + 1; ch++) {
|
|
//----- SyncBox
|
|
connect(cbbOnOff[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbOnOff, ch);});
|
|
connect(spbDCOffset[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbDCOffset, ch);});
|
|
connect(spbThreshold[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbThreshold, ch);});
|
|
connect(cbbParity[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbParity, ch);});
|
|
connect(spbRecordLength[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbRecordLength, ch);});
|
|
connect(spbPreTrigger[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbPreTrigger, ch);});
|
|
|
|
connect(cbbWaveSource[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveSource, ch);});
|
|
connect(cbbWaveRes[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveRes, ch);});
|
|
connect(cbbWaveSave[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveSave, ch);});
|
|
|
|
connect(cbbAnaProbe0[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbAnaProbe0, ch);});
|
|
connect(cbbAnaProbe1[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbAnaProbe1, ch);});
|
|
connect(cbbDigProbe0[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe0, ch);});
|
|
connect(cbbDigProbe1[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe1, ch);});
|
|
connect(cbbDigProbe2[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe2, ch);});
|
|
connect(cbbDigProbe3[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe3, ch);});
|
|
|
|
connect(cbbEventSelector[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbEventSelector, ch);});
|
|
connect(cbbWaveSelector[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveSelector, ch);});
|
|
connect(spbEnergySkimLow[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbEnergySkimLow, ch);});
|
|
connect(spbEnergySkimHigh[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbEnergySkimHigh, ch);});
|
|
|
|
connect(cbbEvtTrigger[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbEvtTrigger, ch);});
|
|
connect(cbbWaveTrigger[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveTrigger, ch);});
|
|
connect(cbbChVetoSrc[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbChVetoSrc, ch);});
|
|
connect(cbbCoinMask[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbCoinMask, ch);});
|
|
connect(cbbAntiCoinMask[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbAntiCoinMask, ch);});
|
|
connect(spbCoinLength[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbCoinLength, ch);});
|
|
connect(spbADCVetoWidth[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbADCVetoWidth, ch);});
|
|
|
|
connect(spbInputRiseTime[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbInputRiseTime, ch);});
|
|
connect(spbTriggerGuard[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbTriggerGuard, ch);});
|
|
connect(cbbLowFilter[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbLowFilter, ch);});
|
|
|
|
connect(spbTrapRiseTime[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbTrapRiseTime, ch);});
|
|
connect(spbTrapFlatTop[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbTrapFlatTop, ch);});
|
|
connect(spbTrapPoleZero[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbTrapPoleZero, ch);});
|
|
|
|
connect(spbPeaking[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbPeaking, ch);});
|
|
connect(spbBaselineGuard[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbBaselineGuard, ch);});
|
|
connect(spbPileupGuard[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbPileupGuard, ch);});
|
|
|
|
connect(cbbBaselineAvg[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbBaselineAvg, ch);});
|
|
connect(cbbPeakingAvg[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbPeakingAvg, ch);});
|
|
connect(spbFineGain[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbFineGain, ch);});
|
|
spbFineGain[digiID][ch]->setSingleStep(0.001);
|
|
spbFineGain[digiID][ch]->setDecimals(3);
|
|
|
|
}
|
|
|
|
|
|
}
|
|
|
|
void DigiSettingsPanel::SetupPSDChannels(unsigned short digiID){
|
|
|
|
//@.......... All Settings tab
|
|
QWidget * tab_All = new QWidget(digiTab[digiID]);
|
|
//tab_All->setStyleSheet("background-color: #EEEEEE");
|
|
chTabWidget[digiID]->addTab(tab_All, "All/Single Ch.");
|
|
|
|
QGridLayout * allLayout = new QGridLayout(tab_All);
|
|
allLayout->setAlignment(Qt::AlignTop);
|
|
|
|
unsigned short ch = digi[digiID]->GetNChannels();
|
|
|
|
{//*--------- Group 0
|
|
box0[digiID] = new QGroupBox("Channel Selection", digiTab[digiID]);
|
|
allLayout->addWidget(box0[digiID]);
|
|
QGridLayout * layout0 = new QGridLayout(box0[digiID]);
|
|
layout0->setAlignment(Qt::AlignLeft);
|
|
|
|
QLabel * lbCh = new QLabel("Channel :", digiTab[digiID]);
|
|
lbCh->setAlignment(Qt::AlignCenter | Qt::AlignRight);
|
|
layout0->addWidget(lbCh, 0, 0);
|
|
|
|
cbChPick[digiID] = new RComboBox(digiTab[digiID]);
|
|
cbChPick[digiID]->addItem("All", -1);
|
|
for( int i = 0; i < ch; i++) cbChPick[digiID]->addItem("Ch-" + QString::number(i), i);
|
|
layout0->addWidget(cbChPick[digiID], 0, 1);
|
|
connect(cbChPick[digiID], &RComboBox::currentIndexChanged, this, [=](){
|
|
int index = cbChPick[ID]->currentData().toInt();
|
|
if(index == -1) {
|
|
UpdatePanelFromMemory();
|
|
return;
|
|
}else{
|
|
enableSignalSlot = false;
|
|
unsigned short ch = digi[digiID]->GetNChannels();
|
|
//printf("index = %d, ch = %d\n", index, ch);
|
|
FillComboBoxValueFromMemory(cbbOnOff[ID][ch], PHA::CH::ChannelEnable, index);
|
|
FillSpinBoxValueFromMemory(spbDCOffset[ID][ch], PHA::CH::DC_Offset, index);
|
|
FillSpinBoxValueFromMemory(spbThreshold[ID][ch], PHA::CH::TriggerThreshold, index);
|
|
FillComboBoxValueFromMemory(cbbParity[ID][ch], PHA::CH::Polarity, index);
|
|
FillSpinBoxValueFromMemory(spbRecordLength[ID][ch], PHA::CH::RecordLength, index);
|
|
FillSpinBoxValueFromMemory(spbPreTrigger[ID][ch], PHA::CH::PreTrigger, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbWaveSource[ID][ch], PHA::CH::WaveDataSource, index);
|
|
FillComboBoxValueFromMemory(cbbWaveRes[ID][ch], PHA::CH::WaveResolution, index);
|
|
FillComboBoxValueFromMemory(cbbWaveSave[ID][ch], PHA::CH::WaveSaving, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbAnaProbe0[ID][ch], PHA::CH::WaveAnalogProbe0, index);
|
|
FillComboBoxValueFromMemory(cbbAnaProbe1[ID][ch], PHA::CH::WaveAnalogProbe1, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe0[ID][ch], PHA::CH::WaveDigitalProbe0, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe1[ID][ch], PHA::CH::WaveDigitalProbe1, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe2[ID][ch], PHA::CH::WaveDigitalProbe2, index);
|
|
FillComboBoxValueFromMemory(cbbDigProbe3[ID][ch], PHA::CH::WaveDigitalProbe3, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbEventSelector[ID][ch], PHA::CH::EventSelector, index);
|
|
FillComboBoxValueFromMemory(cbbWaveSelector[ID][ch], PHA::CH::WaveSelector, index);
|
|
FillSpinBoxValueFromMemory(spbEnergySkimLow[ID][ch], PHA::CH::EnergySkimLowDiscriminator, index);
|
|
FillSpinBoxValueFromMemory(spbEnergySkimHigh[ID][ch], PHA::CH::EnergySkimHighDiscriminator, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbEvtTrigger[ID][ch], PHA::CH::EventTriggerSource, index);
|
|
FillComboBoxValueFromMemory(cbbWaveTrigger[ID][ch], PHA::CH::WaveTriggerSource, index);
|
|
FillComboBoxValueFromMemory(cbbChVetoSrc[ID][ch], PHA::CH::ChannelVetoSource, index);
|
|
FillComboBoxValueFromMemory(cbbCoinMask[ID][ch], PHA::CH::CoincidenceMask, index);
|
|
FillComboBoxValueFromMemory(cbbAntiCoinMask[ID][ch], PHA::CH::AntiCoincidenceMask, index);
|
|
FillSpinBoxValueFromMemory(spbCoinLength[ID][ch], PHA::CH::CoincidenceLength, index);
|
|
FillSpinBoxValueFromMemory(spbADCVetoWidth[ID][ch], PHA::CH::ADCVetoWidth, index);
|
|
|
|
unsigned long mask = Utility::TenBase(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, cbChPick[ID]->currentData().toInt()));
|
|
leTriggerMask[ID][ch]->setText("0x" + QString::number(mask, 16).toUpper());
|
|
|
|
//-------- PSD
|
|
FillComboBoxValueFromMemory(cbbADCInputBaselineAvg[ID][ch], PSD::CH::ADCInputBaselineAvg, index);
|
|
FillSpinBoxValueFromMemory(spbAbsBaseline[ID][ch], PSD::CH::AbsoluteBaseline, index);
|
|
FillSpinBoxValueFromMemory(spbADCInputBaselineGuard[ID][ch], PSD::CH::ADCInputBaselineGuard, index);
|
|
|
|
FillComboBoxValueFromMemory(cbbTriggerFilter[ID][ch], PSD::CH::TriggerFilterSelection, index);
|
|
FillComboBoxValueFromMemory(cbbTriggerHysteresis[ID][ch], PSD::CH::TriggerHysteresis, index);
|
|
FillSpinBoxValueFromMemory(spbCFDDelay[ID][ch], PSD::CH::CFDDelay, index);
|
|
FillSpinBoxValueFromMemory(spbCFDFraction[ID][ch], PSD::CH::CFDFraction, index);
|
|
FillComboBoxValueFromMemory(cbbSmoothingFactor[ID][ch], PSD::CH::SmoothingFactor, index);
|
|
FillComboBoxValueFromMemory(cbbChargeSmooting[ID][ch], PSD::CH::ChargeSmoothing, index);
|
|
FillComboBoxValueFromMemory(cbbTimeFilterSmoothing[ID][ch], PSD::CH::TimeFilterSmoothing, index);
|
|
FillSpinBoxValueFromMemory(spbTimeFilterReTriggerGuard[ID][ch], PSD::CH::TimeFilterRetriggerGuard, index);
|
|
FillSpinBoxValueFromMemory(spbPileupGap[ID][ch], PSD::CH::PileupGap, index);
|
|
|
|
FillSpinBoxValueFromMemory(spbGateLong[ID][ch], PSD::CH::GateLongLength, index);
|
|
FillSpinBoxValueFromMemory(spbGateShort[ID][ch], PSD::CH::GateShortLength, index);
|
|
FillSpinBoxValueFromMemory(spbGateOffset[ID][ch], PSD::CH::GateOffset, index);
|
|
FillSpinBoxValueFromMemory(spbLongChargeIntergratorPedestal[ID][ch], PSD::CH::LongChargeIntegratorPedestal, index);
|
|
FillSpinBoxValueFromMemory(spbShortChargeIntergratorPedestal[ID][ch], PSD::CH::ShortChargeIntegratorPedestal, index);
|
|
FillComboBoxValueFromMemory(cbbEnergyGain[ID][ch], PSD::CH::EnergyGain, index);
|
|
|
|
FillSpinBoxValueFromMemory(spbNeutronThreshold[ID][ch], PSD::CH::NeutronThreshold, index);
|
|
FillComboBoxValueFromMemory(cbbEventNeutronReject[ID][ch], PSD::CH::EventNeutronReject, index);
|
|
FillComboBoxValueFromMemory(cbbWaveNeutronReject[ID][ch], PSD::CH::WaveNeutronReject, index);
|
|
|
|
enableSignalSlot = true;
|
|
}
|
|
});
|
|
|
|
}
|
|
|
|
int rowID = 0;
|
|
{//*--------- Group 1
|
|
box1[digiID] = new QGroupBox("Input Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box1[digiID]);
|
|
QGridLayout * layout1 = new QGridLayout(box1[digiID]);
|
|
|
|
rowID = 0;
|
|
SetupComboBox(cbbOnOff[digiID][ch], PHA::CH::ChannelEnable, -1, true, "On/Off", layout1, rowID, 0);
|
|
SetupComboBox(cbbWaveSource[digiID][ch], PHA::CH::WaveDataSource, -1, true, "Wave Data Source", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupComboBox(cbbWaveRes[digiID][ch], PHA::CH::WaveResolution, -1, true, "Wave Resol.", layout1, rowID, 0);
|
|
SetupComboBox(cbbWaveSave[digiID][ch], PHA::CH::WaveSaving, -1, true, "Wave Save", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbDCOffset[digiID][ch], PHA::CH::DC_Offset, -1, true, "DC Offset [%]", layout1, rowID, 0);
|
|
SetupSpinBox(spbThreshold[digiID][ch], PHA::CH::TriggerThreshold, -1, true, "Threshold [LSB]", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbRecordLength[digiID][ch], PHA::CH::RecordLength, -1, true, "Record Length [ns]", layout1, rowID, 0);
|
|
SetupSpinBox(spbPreTrigger[digiID][ch], PHA::CH::PreTrigger, -1, true, "Pre Trigger [ns]", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupComboBox(cbbParity[digiID][ch], PHA::CH::Polarity, -1, true, "Parity", layout1, rowID, 0);
|
|
SetupComboBox(cbbADCInputBaselineAvg[digiID][ch], PSD::CH::ADCInputBaselineAvg, -1, true, "ADC Input BL Avg.", layout1, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbAbsBaseline[digiID][ch], PSD::CH::AbsoluteBaseline, -1, true, "Abs. Baseline", layout1, rowID, 0);
|
|
SetupSpinBox(spbADCInputBaselineGuard[digiID][ch], PSD::CH::ADCInputBaselineGuard, -1, true, "ADC Input BL Gaurd [ns]", layout1, rowID, 2);
|
|
|
|
}
|
|
|
|
{//*--------- Group 2
|
|
box3[digiID] = new QGroupBox("Gate Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box3[digiID]);
|
|
QGridLayout * layout3 = new QGridLayout(box3[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0;
|
|
SetupSpinBox(spbGateLong[digiID][ch], PSD::CH::GateLongLength, -1, true, "Long Gate [ns]", layout3, rowID, 0);
|
|
SetupSpinBox(spbGateShort[digiID][ch], PSD::CH::GateShortLength, -1, true, "Short Gate [ns]", layout3, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbGateOffset[digiID][ch], PSD::CH::GateOffset, -1, true, "Gate Offset [ns]", layout3, rowID, 0);
|
|
SetupComboBox(cbbEnergyGain[digiID][ch], PSD::CH::EnergyGain, -1, true, "Energy Gain", layout3, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbLongChargeIntergratorPedestal[digiID][ch], PSD::CH::LongChargeIntegratorPedestal, -1, true, "Long Ped.", layout3, rowID, 0);
|
|
SetupSpinBox(spbShortChargeIntergratorPedestal[digiID][ch], PSD::CH::ShortChargeIntegratorPedestal, -1, true, "Short Ped.", layout3, rowID, 2);
|
|
|
|
}
|
|
|
|
{//*--------- Group 4
|
|
box4[digiID] = new QGroupBox("Probe Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box4[digiID]);
|
|
QGridLayout * layout4 = new QGridLayout(box4[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0;
|
|
SetupComboBox(cbbAnaProbe0[digiID][ch], PSD::CH::WaveAnalogProbe0, -1, true, "Analog Prob. 0", layout4, rowID, 0, 1, 2);
|
|
SetupComboBox(cbbAnaProbe1[digiID][ch], PSD::CH::WaveAnalogProbe1, -1, true, "Analog Prob. 1", layout4, rowID, 3, 1, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbDigProbe0[digiID][ch], PSD::CH::WaveDigitalProbe0, -1, true, "Digitial Prob. 0", layout4, rowID, 0, 1, 2);
|
|
SetupComboBox(cbbDigProbe1[digiID][ch], PSD::CH::WaveDigitalProbe1, -1, true, "Digitial Prob. 1", layout4, rowID, 3, 1, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbDigProbe2[digiID][ch], PSD::CH::WaveDigitalProbe2, -1, true, "Digitial Prob. 2", layout4, rowID, 0, 1, 2);
|
|
SetupComboBox(cbbDigProbe3[digiID][ch], PSD::CH::WaveDigitalProbe3, -1, true, "Digitial Prob. 3", layout4, rowID, 3, 1, 2);
|
|
|
|
}
|
|
|
|
{//*--------- Group 5
|
|
box5[digiID] = new QGroupBox("Trigger Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box5[digiID]);
|
|
QGridLayout * layout5 = new QGridLayout(box5[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0;
|
|
SetupComboBox(cbbEvtTrigger[digiID][ch], PHA::CH::EventTriggerSource, -1, true, "Event Trig. Source", layout5, rowID, 0);
|
|
SetupComboBox(cbbWaveTrigger[digiID][ch], PHA::CH::WaveTriggerSource, -1, true, "Wave Trig. Source", layout5, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbChVetoSrc[digiID][ch], PHA::CH::ChannelVetoSource, -1, true, "Veto Source", layout5, rowID, 0);
|
|
|
|
QLabel * lbTrgMsk = new QLabel("Trigger Mask");
|
|
lbTrgMsk->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
layout5->addWidget(lbTrgMsk, rowID, 2);
|
|
leTriggerMask[digiID][ch] = new QLineEdit(this);
|
|
leTriggerMask[digiID][ch]->setToolTip("Both Hex or Dec is OK.");
|
|
layout5->addWidget(leTriggerMask[digiID][ch], rowID, 3);
|
|
|
|
connect(leTriggerMask[digiID][ch], &QLineEdit::textChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
leTriggerMask[digiID][ch]->setStyleSheet("color:blue;");
|
|
});
|
|
|
|
connect(leTriggerMask[digiID][ch], &QLineEdit::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
int index = cbChPick[ID]->currentData().toInt();
|
|
|
|
QString SixteenBaseValue = "0x" + QString::number(Utility::TenBase(leTriggerMask[ID][ch]->text().toStdString()), 16).toUpper();
|
|
leTriggerMask[ID][ch]->setText(SixteenBaseValue);
|
|
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::CH::ChannelsTriggerMask.GetPara()) ;
|
|
msg += ",CH:" + (index == -1 ? "All" : QString::number(index));
|
|
msg += " = " + SixteenBaseValue;
|
|
|
|
if( digi[ID]->WriteValue(PHA::CH::ChannelsTriggerMask, SixteenBaseValue.toStdString(), index)){
|
|
SendLogMsg(msg + "|OK.");
|
|
leTriggerMask[ID][ch]->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
leTriggerMask[ID][ch]->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbCoinMask[digiID][ch], PHA::CH::CoincidenceMask, -1, true, "Coin. Mask", layout5, rowID, 0);
|
|
SetupComboBox(cbbAntiCoinMask[digiID][ch], PHA::CH::AntiCoincidenceMask, -1, true, "Anti-Coin. Mask", layout5, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupSpinBox(spbCoinLength[digiID][ch], PHA::CH::CoincidenceLength, -1, true, "Coin. Length [ns]", layout5, rowID, 0);
|
|
SetupSpinBox(spbADCVetoWidth[digiID][ch], PHA::CH::ADCVetoWidth, -1, true, "ADC Veto Length [ns]", layout5, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbTriggerFilter[digiID][ch], PSD::CH::TriggerFilterSelection, -1, true, "Trig. Filter", layout5, rowID, 0);
|
|
SetupComboBox(cbbTriggerHysteresis[digiID][ch], PSD::CH::TriggerHysteresis, -1, true, "Trig. Hysteresis", layout5, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbPileupGap[digiID][ch], PSD::CH::PileupGap, -1, true, "Pile-Up Gap [ns]", layout5, rowID, 0);
|
|
SetupSpinBox(spbTimeFilterReTriggerGuard[digiID][ch], PSD::CH::TimeFilterRetriggerGuard,-1, true, "Time Filter Re.Trg Guard [ns]", layout5, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupSpinBox(spbCFDDelay[digiID][ch], PSD::CH::CFDDelay, -1, true, "CFD Delay [ns]", layout5, rowID, 0);
|
|
SetupSpinBox(spbCFDFraction[digiID][ch], PSD::CH::CFDFraction, -1, true, "CFD Frac. [%]", layout5, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupComboBox(cbbSmoothingFactor[digiID][ch], PSD::CH::SmoothingFactor, -1, true, "Smoothing Fact.", layout5, rowID, 0);
|
|
SetupComboBox(cbbChargeSmooting[digiID][ch], PSD::CH::ChargeSmoothing, -1, true, "Charge Smoothing", layout5, rowID, 2);
|
|
|
|
rowID ++;
|
|
SetupComboBox(cbbTimeFilterSmoothing[digiID][ch], PSD::CH::TimeFilterSmoothing, -1, true, "Time Filter Smoothing", layout5, rowID, 0);
|
|
|
|
for( int i = 0; i < layout5->columnCount(); i++) layout5->setColumnStretch(i, 1);
|
|
|
|
}
|
|
|
|
{//*--------- Group 6
|
|
box6[digiID] = new QGroupBox("Other Settings", digiTab[digiID]);
|
|
allLayout->addWidget(box6[digiID]);
|
|
QGridLayout * layout6 = new QGridLayout(box6[digiID]);
|
|
|
|
//------------------------------
|
|
rowID = 0 ;
|
|
SetupComboBox(cbbEventSelector[digiID][ch], PHA::CH::EventSelector, -1, true, "Event Selector", layout6, rowID, 0);
|
|
SetupComboBox(cbbWaveSelector[digiID][ch], PHA::CH::WaveSelector, -1, true, "Wave Selector", layout6, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupSpinBox(spbEnergySkimLow[digiID][ch], PHA::CH::EnergySkimLowDiscriminator, -1, true, "Energy Skim Low", layout6, rowID, 0);
|
|
SetupSpinBox(spbEnergySkimHigh[digiID][ch], PHA::CH::EnergySkimHighDiscriminator, -1, true, "Energy Skim High", layout6, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupComboBox(cbbEventNeutronReject[digiID][ch], PSD::CH::EventNeutronReject, -1, true, "Event Neutron Rej.", layout6, rowID, 0);
|
|
SetupComboBox(cbbWaveNeutronReject[digiID][ch], PSD::CH::WaveNeutronReject, -1, true, "Wave Neutron Rej.", layout6, rowID, 2);
|
|
|
|
//------------------------------
|
|
rowID ++;
|
|
SetupSpinBox(spbNeutronThreshold[digiID][ch], PSD::CH::NeutronThreshold, -1, true, "Neutron Threshold", layout6, rowID, 0);
|
|
|
|
}
|
|
|
|
{//@============== input tab
|
|
inputTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(inputTab[digiID], "Input");
|
|
|
|
SetupComboBoxTab(cbbOnOff, PHA::CH::ChannelEnable, "On/Off", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveSource, PHA::CH::WaveDataSource, "Wave Data Dource", inputTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbWaveRes, PHA::CH::WaveResolution, "Wave Resol.", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveSave, PHA::CH::WaveSaving, "Wave Save", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbDCOffset, PHA::CH::DC_Offset, "DC Offset [%]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbThreshold, PHA::CH::TriggerThreshold, "Threshold [LSB]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbRecordLength, PHA::CH::RecordLength, "Record Length [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbPreTrigger, PHA::CH::PreTrigger, "PreTrigger [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbParity, PHA::CH::Polarity, "Parity", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
SetupComboBoxTab(cbbADCInputBaselineAvg, PSD::CH::ADCInputBaselineAvg, "ADC Input BL Avg.", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbAbsBaseline, PSD::CH::AbsoluteBaseline, "Abs. Baseline", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbADCInputBaselineGuard, PSD::CH::ADCInputBaselineGuard, "ADC Input BL Gaurd [ns]", inputTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
|
|
for( int ch = 0; ch < digi[digiID]->GetNChannels(); ch++){
|
|
//Set color of some combox
|
|
cbbOnOff[digiID][ch]->setItemData(1, QBrush(orangeColor), Qt::ForegroundRole);
|
|
connect(cbbOnOff[digiID][ch], &RComboBox::currentIndexChanged, this, [=](int index){ cbbOnOff[ID][ch]->setStyleSheet(index == 1 ? "color : orange;" : "");});
|
|
cbbParity[digiID][ch]->setItemData(1, QBrush(orangeColor), Qt::ForegroundRole);
|
|
connect(cbbParity[digiID][ch], &RComboBox::currentIndexChanged, this, [=](int index){ cbbParity[ID][ch]->setStyleSheet(index == 1 ? "color : orange;" : "");});
|
|
}
|
|
|
|
}
|
|
|
|
{//@============== PSD Gate tab
|
|
trapTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(trapTab[digiID], "Gate");
|
|
|
|
SetupSpinBoxTab(spbGateLong, PSD::CH::GateLongLength, "Long Gate [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbGateShort, PSD::CH::GateShortLength, "Short Gate [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbGateOffset, PSD::CH::GateOffset, "Gate Offset [ns]", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbEnergyGain, PSD::CH::EnergyGain, "Energy Gain", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbLongChargeIntergratorPedestal, PSD::CH::LongChargeIntegratorPedestal, "Long Ped.", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbShortChargeIntergratorPedestal, PSD::CH::ShortChargeIntegratorPedestal, "Short Ped.", trapTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
}
|
|
|
|
{//@============== Probe tab
|
|
probeTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(probeTab[digiID], "Probe");
|
|
|
|
SetupComboBoxTab(cbbAnaProbe0, PSD::CH::WaveAnalogProbe0, "Analog Prob. 0", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbAnaProbe1, PSD::CH::WaveAnalogProbe1, "Analog Prob. 1", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe0, PSD::CH::WaveDigitalProbe0, "Digital Prob. 0", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe1, PSD::CH::WaveDigitalProbe1, "Digital Prob. 1", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe2, PSD::CH::WaveDigitalProbe2, "Digital Prob. 2", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
SetupComboBoxTab(cbbDigProbe3, PSD::CH::WaveDigitalProbe3, "Digital Prob. 3", probeTab[digiID], digiID, digi[digiID]->GetNChannels(), 4);
|
|
}
|
|
|
|
{//@============== Other tab
|
|
otherTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(otherTab[digiID], "Others");
|
|
|
|
SetupComboBoxTab(cbbEventSelector, PHA::CH::EventSelector, "Event Selector", otherTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveSelector, PHA::CH::WaveSelector, "Wave Selector", otherTab[digiID], digiID, digi[digiID]->GetNChannels(), 2 );
|
|
SetupSpinBoxTab(spbEnergySkimLow, PHA::CH::EnergySkimLowDiscriminator, "Energy Skim Low", otherTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbEnergySkimHigh, PHA::CH::EnergySkimHighDiscriminator, "Energy Skim High", otherTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
}
|
|
|
|
{//@============== Trigger tab
|
|
triggerTab[digiID] = new QTabWidget(digiTab[digiID]);
|
|
chTabWidget[digiID]->addTab(triggerTab[digiID], "Trigger");
|
|
|
|
SetupComboBoxTab(cbbEvtTrigger, PHA::CH::EventTriggerSource, "Event Trig. Source", triggerTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbWaveTrigger, PHA::CH::WaveTriggerSource, "Wave Trig. Source", triggerTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbChVetoSrc, PHA::CH::ChannelVetoSource, "Veto Source", triggerTab[digiID], digiID, digi[digiID]->GetNChannels(), 2);
|
|
SetupComboBoxTab(cbbCoinMask, PHA::CH::CoincidenceMask, "Coin. Mask", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbAntiCoinMask, PHA::CH::AntiCoincidenceMask, "Anti-Coin. Mask", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbCoinLength, PHA::CH::CoincidenceLength, "Coin. Length [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbADCVetoWidth, PHA::CH::ADCVetoWidth, "ADC Veto Length [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
|
|
SetupComboBoxTab(cbbTriggerFilter, PSD::CH::TriggerFilterSelection, "Trig. Filter", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbTriggerHysteresis, PSD::CH::TriggerHysteresis, "Trig. Hysteresis", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbPileupGap, PSD::CH::PileupGap, "Pile-Up Gap [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbTimeFilterReTriggerGuard, PSD::CH::TimeFilterRetriggerGuard, "Time Filter Re.Trg Guard [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbCFDDelay, PSD::CH::CFDDelay, "CFD Delay [ns]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbCFDFraction, PSD::CH::CFDFraction, "CFD Frac. [%]", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbSmoothingFactor, PSD::CH::SmoothingFactor, "Smoothing Fact.", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbChargeSmooting, PSD::CH::ChargeSmoothing, "Charge Smoothing", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbTimeFilterSmoothing, PSD::CH::TimeFilterSmoothing, "Time Filter Smoothing", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
SetupComboBoxTab(cbbEventNeutronReject, PSD::CH::EventNeutronReject, "Event Neutron Rej.", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupComboBoxTab(cbbWaveNeutronReject, PSD::CH::WaveNeutronReject, "Wave Neutron Rej.", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
SetupSpinBoxTab(spbNeutronThreshold, PSD::CH::NeutronThreshold, "Neutron Threshold", triggerTab[digiID], digiID, digi[digiID]->GetNChannels());
|
|
|
|
}
|
|
|
|
for( int ch = 0; ch < digi[digiID]->GetNChannels() + 1; ch++) {
|
|
//----- SyncBox
|
|
connect(cbbOnOff[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbOnOff, ch);});
|
|
connect(spbDCOffset[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbDCOffset, ch);});
|
|
connect(spbThreshold[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbThreshold, ch);});
|
|
connect(cbbParity[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbParity, ch);});
|
|
connect(spbRecordLength[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbRecordLength, ch);});
|
|
connect(spbPreTrigger[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbPreTrigger, ch);});
|
|
|
|
connect(cbbWaveSource[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveSource, ch);});
|
|
connect(cbbWaveRes[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveRes, ch);});
|
|
connect(cbbWaveSave[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveSave, ch);});
|
|
|
|
connect(cbbAnaProbe0[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbAnaProbe0, ch);});
|
|
connect(cbbAnaProbe1[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbAnaProbe1, ch);});
|
|
connect(cbbDigProbe0[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe0, ch);});
|
|
connect(cbbDigProbe1[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe1, ch);});
|
|
connect(cbbDigProbe2[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe2, ch);});
|
|
connect(cbbDigProbe3[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbDigProbe3, ch);});
|
|
|
|
connect(cbbEventSelector[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbEventSelector, ch);});
|
|
connect(cbbWaveSelector[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveSelector, ch);});
|
|
connect(spbEnergySkimLow[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbEnergySkimLow, ch);});
|
|
connect(spbEnergySkimHigh[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbEnergySkimHigh, ch);});
|
|
|
|
connect(cbbEvtTrigger[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbEvtTrigger, ch);});
|
|
connect(cbbWaveTrigger[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveTrigger, ch);});
|
|
connect(cbbChVetoSrc[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbChVetoSrc, ch);});
|
|
connect(cbbCoinMask[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbCoinMask, ch);});
|
|
connect(cbbAntiCoinMask[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbAntiCoinMask, ch);});
|
|
connect(spbCoinLength[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbCoinLength, ch);});
|
|
connect(spbADCVetoWidth[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbADCVetoWidth, ch);});
|
|
|
|
|
|
connect(cbbADCInputBaselineAvg[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbADCInputBaselineAvg, ch);});
|
|
connect(spbAbsBaseline[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbAbsBaseline, ch);});
|
|
connect(spbADCInputBaselineGuard[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbADCInputBaselineGuard, ch);});
|
|
|
|
connect(cbbTriggerFilter[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbTriggerFilter, ch);});
|
|
connect(cbbTriggerHysteresis[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbTriggerHysteresis, ch);});
|
|
connect(spbCFDDelay[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbCFDDelay, ch);});
|
|
connect(spbCFDFraction[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbCFDFraction, ch);});
|
|
connect(cbbSmoothingFactor[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbSmoothingFactor, ch);});
|
|
connect(cbbChargeSmooting[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbChargeSmooting, ch);});
|
|
connect(cbbTimeFilterSmoothing[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbTimeFilterSmoothing, ch);});
|
|
connect(spbTimeFilterReTriggerGuard[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbTimeFilterReTriggerGuard, ch);});
|
|
connect(spbPileupGap[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbPileupGap, ch);});
|
|
|
|
connect(spbGateLong[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbGateLong, ch);});
|
|
connect(spbGateShort[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbGateShort, ch);});
|
|
connect(spbGateOffset[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbGateOffset, ch);});
|
|
connect(spbLongChargeIntergratorPedestal[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbLongChargeIntergratorPedestal, ch);});
|
|
connect(spbShortChargeIntergratorPedestal[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbShortChargeIntergratorPedestal, ch);});
|
|
connect(cbbEnergyGain[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbEnergyGain, ch);});
|
|
|
|
connect(spbNeutronThreshold[digiID][ch], &RSpinBox::returnPressed, this, [=](){ SyncSpinBox(spbNeutronThreshold, ch);});
|
|
connect(cbbEventNeutronReject[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbEventNeutronReject, ch);});
|
|
connect(cbbWaveNeutronReject[digiID][ch], &RComboBox::currentIndexChanged, this, [=](){ SyncComboBox(cbbWaveNeutronReject, ch);});
|
|
|
|
}
|
|
|
|
}
|
|
|
|
//^================================================================
|
|
void DigiSettingsPanel::onTriggerClick(int haha){
|
|
|
|
unsigned short iDig = haha >> 16;
|
|
unsigned short ch = (haha >> 8 ) & 0xFF;
|
|
unsigned short ch2 = haha & 0xFF;
|
|
|
|
//qDebug() << "Digi-" << iDig << ", Ch-" << ch << ", " << ch2;
|
|
|
|
if(trgMapClickStatus[iDig][ch][ch2]){
|
|
trgMap[iDig][ch][ch2]->setStyleSheet("");
|
|
trgMapClickStatus[iDig][ch][ch2] = false;
|
|
}else{
|
|
trgMap[iDig][ch][ch2]->setStyleSheet("background-color: red;");
|
|
trgMapClickStatus[iDig][ch][ch2] = true;
|
|
}
|
|
|
|
//format triggermask for ch;
|
|
unsigned long mask = 0;
|
|
for( int i = 0; i < digi[iDig]->GetNChannels(); i++){
|
|
if( trgMapClickStatus[iDig][ch][i] ) {
|
|
mask += (1ULL << i);
|
|
}
|
|
}
|
|
|
|
QString kaka = QString::number(mask);
|
|
|
|
QString msg;
|
|
msg = "DIG:" + QString::number(digi[iDig]->GetNChannels()) + ",CH:" + QString::number(ch) + "|" + QString::fromStdString(PHA::CH::ChannelsTriggerMask.GetPara() ) + " = 0x" + QString::number(mask,16);
|
|
|
|
if( digi[iDig]->WriteValue(PHA::CH::ChannelsTriggerMask, kaka.toStdString(), ch) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
digi[iDig]->ReadValue(PHA::CH::ChannelsTriggerMask, ch);
|
|
}
|
|
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
|
|
}
|
|
|
|
void DigiSettingsPanel::ReadTriggerMap(){
|
|
|
|
enableSignalSlot = false;
|
|
|
|
//printf("%s\n", __func__);
|
|
|
|
// cbAllEvtTrigger[ID]->setCurrentIndex(cbbEvtTrigger[ID][MaxNumberOfChannel]->currentIndex());
|
|
// cbAllWaveTrigger[ID]->setCurrentIndex(cbbWaveTrigger[ID][MaxNumberOfChannel]->currentIndex());
|
|
// cbAllCoinMask[ID]->setCurrentIndex(cbbCoinMask[ID][MaxNumberOfChannel]->currentIndex());
|
|
// cbAllAntiCoinMask[ID]->setCurrentIndex(cbbAntiCoinMask[ID][MaxNumberOfChannel]->currentIndex());
|
|
// sbAllCoinLength[ID]->setValue(spbCoinLength[ID][MaxNumberOfChannel]->value());
|
|
|
|
for( int ch = 0; ch < (int) digi[ID]->GetNChannels(); ch ++){
|
|
|
|
unsigned long mask = Utility::TenBase(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, ch));
|
|
//printf("Trigger Mask of ch-%2d : 0x%s |%s| \n", ch, QString::number(mask, 16).toStdString().c_str(), digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, ch).c_str());
|
|
|
|
for( int k = 0; k < (int) digi[ID]->GetNChannels(); k ++ ){
|
|
trgMapClickStatus[ID][ch][k] = ( (mask >> k) & 0x1 );
|
|
if( (mask >> k) & 0x1 ){
|
|
trgMap[ID][ch][k]->setStyleSheet("background-color: red;");
|
|
}else{
|
|
trgMap[ID][ch][k]->setStyleSheet("");
|
|
}
|
|
}
|
|
}
|
|
|
|
enableSignalSlot = true;
|
|
}
|
|
|
|
//^================================================================
|
|
|
|
void DigiSettingsPanel::RefreshSettings(){
|
|
printf("DigiSettingsPanel::%s\n", __func__);
|
|
digi[ID]->ReadAllSettings();
|
|
UpdatePanelFromMemory();
|
|
}
|
|
|
|
void DigiSettingsPanel::UpdateStatus(){
|
|
|
|
if( tabWidget->currentIndex() >= nDigi) return;
|
|
|
|
digi[ID]->ReadValue(PHA::DIG::LED_status);
|
|
digi[ID]->ReadValue(PHA::DIG::ACQ_status);
|
|
|
|
for( int i = 0; i < (int) PHA::DIG::TempSensADC.size(); i++){
|
|
if( digi[ID]->GetModelName() != "VX2745" && i > 0 ) continue;
|
|
digi[ID]->ReadValue(PHA::DIG::TempSensADC[i]);
|
|
}
|
|
for( int i = 0; i < (int) PHA::DIG::TempSensOthers.size(); i++){
|
|
digi[ID]->ReadValue(PHA::DIG::TempSensOthers[i]);
|
|
}
|
|
|
|
UpdatePanelFromMemory(true);
|
|
|
|
}
|
|
|
|
void DigiSettingsPanel::EnableControl(){
|
|
|
|
UpdatePanelFromMemory();
|
|
|
|
for( int id = 0; id < nDigi; id ++){
|
|
bool enable = !digi[id]->IsAcqOn();
|
|
|
|
//digiBox[id]->setEnabled(enable);
|
|
//if( digi[id]->GetFPGAType() == "DPP_PHA") VGABox[id]->setEnabled(enable);
|
|
//if( ckbGlbTrgSource[id][3]->isChecked() ) testPulseBox[id]->setEnabled(enable);
|
|
|
|
bdCfg[id]->setEnabled(enable);
|
|
// bdTestPulse[id]->setEnabled(enable);
|
|
bdVGA[id]->setEnabled(enable);
|
|
bdLVDS[id]->setEnabled(enable);
|
|
bdITL[id]->setEnabled(enable);
|
|
|
|
box1[id]->setEnabled(enable);
|
|
box3[id]->setEnabled(enable);
|
|
box4[id]->setEnabled(enable);
|
|
box5[id]->setEnabled(enable);
|
|
box6[id]->setEnabled(enable);
|
|
|
|
bnReadSettngs[id]->setEnabled(enable);
|
|
bnResetBd[id]->setEnabled(enable);
|
|
bnDefaultSetting[id]->setEnabled(enable);
|
|
bnSaveSettings[id]->setEnabled(enable);
|
|
bnLoadSettings[id]->setEnabled(enable);
|
|
bnClearData[id]->setEnabled(enable);
|
|
bnArmACQ[id]->setEnabled(enable);
|
|
bnDisarmACQ[id]->setEnabled(enable);
|
|
bnSoftwareStart[id]->setEnabled(enable);
|
|
bnSoftwareStop[id]->setEnabled(enable);
|
|
|
|
if( digi[id]->GetFPGAType() != "DPP_PHA" || digi[id]->GetModelName() != "VX2745" ) bdVGA[id]->setEnabled(false);
|
|
|
|
QVector<QTabWidget*> tempArray = {inputTab[id], trapTab[id], probeTab[id], otherTab[id] };
|
|
|
|
for( int k = 0; k < tempArray.size(); k++){
|
|
for( int i = 0; i < tempArray[k]->count(); i++) {
|
|
if( k == 0 && (i == 0 || i == 1 || i == 2 ) ) continue;
|
|
QWidget* currentTab = tempArray[k]->widget(i);
|
|
if( currentTab ){
|
|
QList<QWidget*> childWidgets = currentTab->findChildren<QWidget*>();
|
|
for(int j=0; j<childWidgets.count(); j++) {
|
|
childWidgets[j]->setEnabled(enable);
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
//triggerMapTab[ID]->setEnabled(enable);
|
|
|
|
icBox1->setEnabled(enable);
|
|
icBox2->setEnabled(enable);
|
|
}
|
|
|
|
}
|
|
|
|
void DigiSettingsPanel::SaveSettings(){
|
|
|
|
//Check path exist
|
|
QDir dir(digiSettingPath);
|
|
if( !dir.exists() ) dir.mkpath(".");
|
|
|
|
QString filePath = QFileDialog::getSaveFileName(this, "Save Settings File", digiSettingPath, "Data file (*.dat);;Text files (*.txt);;All files (*.*)");
|
|
|
|
if (!filePath.isEmpty()) {
|
|
|
|
QFileInfo fileInfo(filePath);
|
|
QString ext = fileInfo.suffix();
|
|
if( ext == "") filePath += ".dat";
|
|
|
|
int flag = digi[ID]->SaveSettingsToFile(filePath.toStdString().c_str());
|
|
|
|
switch (flag) {
|
|
case 1 : {
|
|
leSettingFile[ID]->setText(filePath);
|
|
SendLogMsg("Saved setting file <b>" + filePath + "</b>.");
|
|
}; break;
|
|
case 0 : {
|
|
leSettingFile[ID]->setText("fail to write setting file.");
|
|
SendLogMsg("<font style=\"color:red;\"> Fail to write setting file. <b>" + filePath + "</b></font>");
|
|
}; break;
|
|
|
|
case -1 : {
|
|
leSettingFile[ID]->setText("fail to save setting file, same settings are empty.");
|
|
SendLogMsg("<font style=\"color:red;\"> Fail to save setting file <b>" + filePath + "</b>, same settings are empty.</font>");
|
|
}; break;
|
|
};
|
|
|
|
}
|
|
|
|
}
|
|
|
|
void DigiSettingsPanel::LoadSettings(){
|
|
QFileDialog fileDialog(this);
|
|
fileDialog.setDirectory(digiSettingPath);
|
|
fileDialog.setFileMode(QFileDialog::ExistingFile);
|
|
fileDialog.setNameFilter("Data file (*.dat);;Text file (*.txt);;All file (*.*)");
|
|
int result = fileDialog.exec();
|
|
|
|
if( ! (result == QDialog::Accepted) ) return;
|
|
|
|
if( fileDialog.selectedFiles().size() == 0 ) return; // when no file selected.
|
|
|
|
QString fileName = fileDialog.selectedFiles().at(0);
|
|
|
|
leSettingFile[ID]->setText(fileName);
|
|
//TODO ==== check is the file valid;
|
|
|
|
if( digi[ID]->LoadSettingsFromFile(fileName.toStdString().c_str()) ){
|
|
SendLogMsg("Loaded settings file " + fileName + " for Digi-" + QString::number(digi[ID]->GetSerialNumber()));
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg("Fail to Loaded settings file " + fileName + " for Digi-" + QString::number(digi[ID]->GetSerialNumber()));
|
|
}
|
|
|
|
}
|
|
|
|
void DigiSettingsPanel::SetDefaultPHASettigns(){
|
|
SendLogMsg("Program Digitizer-" + QString::number(digi[ID]->GetSerialNumber()) + " to default " + QString::fromStdString(digi[ID]->GetFPGAType()));
|
|
digi[ID]->ProgramBoard();
|
|
digi[ID]->ProgramChannels();
|
|
RefreshSettings();
|
|
}
|
|
|
|
void DigiSettingsPanel::UpdatePanelFromMemory(bool onlyStatus){
|
|
|
|
if( !isVisible() ) return;
|
|
|
|
enableSignalSlot = false;
|
|
|
|
if( onlyStatus){
|
|
//printf("DigiSettingsPanel::%s Digi-%d [Only Board Status]\n", __func__, digi[ID]->GetSerialNumber());
|
|
}else{
|
|
printf("DigiSettingsPanel::%s Digi-%d\n", __func__, digi[ID]->GetSerialNumber());
|
|
}
|
|
|
|
//--------- LED Status
|
|
unsigned int ledStatus = atoi(digi[ID]->GetSettingValueFromMemory(PHA::DIG::LED_status).c_str());
|
|
for( int i = 0; i < 19; i++){
|
|
if( (ledStatus >> i) & 0x1 ) {
|
|
LEDStatus[ID][i]->setStyleSheet("background-color:green;");
|
|
}else{
|
|
LEDStatus[ID][i]->setStyleSheet("");
|
|
}
|
|
}
|
|
|
|
//--------- ACQ Status
|
|
unsigned int acqStatus = atoi(digi[ID]->GetSettingValueFromMemory(PHA::DIG::ACQ_status).c_str());
|
|
for( int i = 0; i < 7; i++){
|
|
if( (acqStatus >> i) & 0x1 ) {
|
|
ACQStatus[ID][i]->setStyleSheet("background-color:green;");
|
|
}else{
|
|
ACQStatus[ID][i]->setStyleSheet("");
|
|
}
|
|
}
|
|
|
|
//-------- temperature
|
|
for( int i = 0; i < 8; i++){
|
|
leTemp[ID][i]->setText(QString::fromStdString(digi[ID]->GetSettingValueFromMemory(PHA::DIG::TempSensADC[i])));
|
|
}
|
|
|
|
if( onlyStatus ) {
|
|
enableSignalSlot = true;
|
|
return;
|
|
}
|
|
|
|
for (unsigned short j = 0; j < (unsigned short) infoIndex.size(); j++){
|
|
Reg reg = infoIndex[j].second;
|
|
QString text = QString::fromStdString(digi[ID]->ReadValue(reg));
|
|
if( reg.GetPara() == PHA::DIG::ADC_SampleRate.GetPara() ) {
|
|
text += " = " + QString::number(digi[ID]->GetTick2ns(), 'f', 1) + " ns" ;
|
|
}
|
|
leInfo[ID][j]->setText(text);
|
|
}
|
|
|
|
//-------- board settings
|
|
FillComboBoxValueFromMemory(cbbClockSource[ID], PHA::DIG::ClockSource);
|
|
|
|
QString result = QString::fromStdString(digi[ID]->GetSettingValueFromMemory(PHA::DIG::StartSource));
|
|
QStringList resultList = result.remove(QChar(' ')).split("|");
|
|
//qDebug() << resultList << "," << resultList.count();
|
|
for( int j = 0; j < (int) PHA::DIG::StartSource.GetAnswers().size(); j++){
|
|
ckbStartSource[ID][j]->setChecked(false);
|
|
for( int i = 0; i < resultList.count(); i++){
|
|
//qDebug() << resultList[i] << ", " << QString::fromStdString((DIGIPARA::DIG::StartSource.GetAnswers())[j].first);
|
|
if( resultList[i] == QString::fromStdString((PHA::DIG::StartSource.GetAnswers())[j].first) ) ckbStartSource[ID][j]->setChecked(true);
|
|
}
|
|
}
|
|
|
|
result = QString::fromStdString(digi[ID]->GetSettingValueFromMemory(PHA::DIG::GlobalTriggerSource));
|
|
resultList = result.remove(QChar(' ')).split("|");
|
|
bdTestPulse[ID]->setEnabled(false);
|
|
for( int j = 0; j < (int) PHA::DIG::GlobalTriggerSource.GetAnswers().size(); j++){
|
|
ckbGlbTrgSource[ID][j]->setChecked(false);
|
|
for( int i = 0; i < resultList.count(); i++){
|
|
if( resultList[i] == QString::fromStdString((PHA::DIG::GlobalTriggerSource.GetAnswers())[j].first) ) {
|
|
ckbGlbTrgSource[ID][j]->setChecked(true);
|
|
if( resultList[i] == "TestPulse" || cbDACoutMode[ID]->currentData().toString().toStdString() == "Square" ) bdTestPulse[ID]->setEnabled(true);
|
|
}
|
|
}
|
|
}
|
|
|
|
FillComboBoxValueFromMemory(cbbTrgOut[ID], PHA::DIG::TrgOutMode);
|
|
FillComboBoxValueFromMemory(cbbGPIO[ID], PHA::DIG::GPIOMode);
|
|
FillComboBoxValueFromMemory(cbbBusyIn[ID], PHA::DIG::BusyInSource);
|
|
FillComboBoxValueFromMemory(cbbSyncOut[ID], PHA::DIG::SyncOutMode);
|
|
FillComboBoxValueFromMemory(cbbAutoDisarmAcq[ID], PHA::DIG::EnableAutoDisarmACQ);
|
|
FillComboBoxValueFromMemory(cbbStatEvents[ID], PHA::DIG::EnableStatisticEvents);
|
|
FillComboBoxValueFromMemory(cbbBdVetoPolarity[ID], PHA::DIG::BoardVetoPolarity);
|
|
FillComboBoxValueFromMemory(cbbBoardVetoSource[ID], PHA::DIG::BoardVetoSource);
|
|
FillComboBoxValueFromMemory(cbbIOLevel[ID], PHA::DIG::IO_Level);
|
|
|
|
FillSpinBoxValueFromMemory(dsbBdVetoWidth[ID], PHA::DIG::BoardVetoWidth);
|
|
FillSpinBoxValueFromMemory(spbRunDelay[ID], PHA::DIG::RunDelay);
|
|
FillSpinBoxValueFromMemory(dsbVolatileClockOutDelay[ID], PHA::DIG::VolatileClockOutDelay);
|
|
FillSpinBoxValueFromMemory(dsbClockOutDelay[ID], PHA::DIG::PermanentClockOutDelay);
|
|
|
|
//------------- test pulse
|
|
FillSpinBoxValueFromMemory(dsbTestPuslePeriod[ID], PHA::DIG::TestPulsePeriod);
|
|
FillSpinBoxValueFromMemory(dsbTestPusleWidth[ID], PHA::DIG::TestPulseWidth);
|
|
FillSpinBoxValueFromMemory(spbTestPusleLowLevel[ID], PHA::DIG::TestPulseLowLevel);
|
|
FillSpinBoxValueFromMemory(spbTestPusleHighLevel[ID], PHA::DIG::TestPulseHighLevel);
|
|
|
|
//------------- ITL
|
|
FillComboBoxValueFromMemory(cbITLAMainLogic[ID], PHA::DIG::ITLAMainLogic);
|
|
FillComboBoxValueFromMemory(cbITLAPairLogic[ID], PHA::DIG::ITLAPairLogic);
|
|
FillComboBoxValueFromMemory(cbITLAPolarity[ID], PHA::DIG::ITLAPolarity);
|
|
FillSpinBoxValueFromMemory( sbITLAMajority[ID], PHA::DIG::ITLAMajorityLev);
|
|
FillSpinBoxValueFromMemory( sbITLAGateWidth[ID], PHA::DIG::ITLAGateWidth);
|
|
|
|
FillComboBoxValueFromMemory(cbITLBMainLogic[ID], PHA::DIG::ITLBMainLogic);
|
|
FillComboBoxValueFromMemory(cbITLBPairLogic[ID], PHA::DIG::ITLBPairLogic);
|
|
FillComboBoxValueFromMemory(cbITLBPolarity[ID], PHA::DIG::ITLBPolarity);
|
|
FillSpinBoxValueFromMemory( sbITLBMajority[ID], PHA::DIG::ITLBMajorityLev);
|
|
FillSpinBoxValueFromMemory( sbITLBGateWidth[ID], PHA::DIG::ITLBGateWidth);
|
|
|
|
//------------- LVDS
|
|
for( int k = 0; k < 4; k ++){
|
|
FillComboBoxValueFromMemory(cbLVDSMode[ID][k], PHA::LVDS::LVDSMode, k);
|
|
FillComboBoxValueFromMemory(cbLVDSDirection[ID][k], PHA::LVDS::LVDSDirection, k);
|
|
}
|
|
leLVDSIOReg[ID]->setText(QString::fromStdString(digi[ID]->GetSettingValueFromMemory(PHA::DIG::LVDSIOReg)));
|
|
|
|
//------------- DAC
|
|
FillComboBoxValueFromMemory(cbDACoutMode[ID], PHA::DIG::DACoutMode);
|
|
FillSpinBoxValueFromMemory(sbDACoutStaticLevel[ID], PHA::DIG::DACoutStaticLevel);
|
|
FillSpinBoxValueFromMemory(sbDACoutChSelect[ID], PHA::DIG::DACoutChSelect);
|
|
|
|
if( cbDACoutMode[ID]->currentData().toString().toStdString() == "Static" ) {
|
|
sbDACoutStaticLevel[ID]->setEnabled(true);
|
|
}else{
|
|
sbDACoutStaticLevel[ID]->setEnabled(false);
|
|
}
|
|
|
|
if( cbDACoutMode[ID]->currentData().toString().toStdString() == "ChInput" ) {
|
|
sbDACoutChSelect[ID]->setEnabled(true);
|
|
}else{
|
|
sbDACoutChSelect[ID]->setEnabled(false);
|
|
}
|
|
|
|
//------------ Group
|
|
if( digi[ID]->GetCupVer() >= MIN_VERSION_GROUP ){
|
|
for( int k = 0 ; k < MaxNumberOfGroup; k++){
|
|
FillSpinBoxValueFromMemory(spbInputDelay[ID][k], PHA::GROUP::InputDelay, k); // PHA = PSD
|
|
}
|
|
}
|
|
|
|
|
|
//@============================== Channel setting/ status
|
|
|
|
for( int ch = 0; ch < digi[ID]->GetNChannels(); ch++){
|
|
|
|
unsigned int status = atoi(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelStatus).c_str());
|
|
for( int i = 0; i < 9; i++){
|
|
if( (status >> i) & 0x1 ) {
|
|
chStatus[ID][ch][i]->setStyleSheet("background-color:green;");
|
|
}else{
|
|
chStatus[ID][ch][i]->setStyleSheet("");
|
|
}
|
|
}
|
|
chGainFactor[ID][ch]->setText(QString::fromStdString(digi[ID]->GetSettingValueFromMemory(PHA::CH::GainFactor, ch)));
|
|
chADCToVolts[ID][ch]->setText(QString::fromStdString(digi[ID]->GetSettingValueFromMemory(PHA::CH::ADCToVolts, ch)));
|
|
|
|
FillComboBoxValueFromMemory(cbbOnOff[ID][ch], PHA::CH::ChannelEnable, ch);
|
|
FillSpinBoxValueFromMemory(spbRecordLength[ID][ch], PHA::CH::RecordLength, ch);
|
|
FillSpinBoxValueFromMemory(spbPreTrigger[ID][ch], PHA::CH::PreTrigger, ch);
|
|
FillSpinBoxValueFromMemory(spbDCOffset[ID][ch], PHA::CH::DC_Offset, ch);
|
|
FillSpinBoxValueFromMemory(spbThreshold[ID][ch], PHA::CH::TriggerThreshold, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbParity[ID][ch], PHA::CH::Polarity, ch);
|
|
FillComboBoxValueFromMemory(cbbWaveSource[ID][ch], PHA::CH::WaveDataSource, ch);
|
|
FillComboBoxValueFromMemory(cbbWaveRes[ID][ch], PHA::CH::WaveResolution, ch);
|
|
FillComboBoxValueFromMemory(cbbWaveSave[ID][ch], PHA::CH::WaveSaving, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbEvtTrigger[ID][ch], PHA::CH::EventTriggerSource, ch);
|
|
FillComboBoxValueFromMemory(cbbWaveTrigger[ID][ch], PHA::CH::WaveTriggerSource, ch);
|
|
FillComboBoxValueFromMemory(cbbCoinMask[ID][ch], PHA::CH::CoincidenceMask, ch);
|
|
FillComboBoxValueFromMemory(cbbAntiCoinMask[ID][ch], PHA::CH::AntiCoincidenceMask, ch);
|
|
FillSpinBoxValueFromMemory(spbCoinLength[ID][ch], PHA::CH::CoincidenceLength, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbChVetoSrc[ID][ch], PHA::CH::ChannelVetoSource, ch);
|
|
FillSpinBoxValueFromMemory(spbADCVetoWidth[ID][ch], PHA::CH::ADCVetoWidth, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbEventSelector[ID][ch], PHA::CH::EventSelector, ch);
|
|
FillComboBoxValueFromMemory(cbbWaveSelector[ID][ch], PHA::CH::WaveSelector, ch);
|
|
FillSpinBoxValueFromMemory(spbEnergySkimLow[ID][ch], PHA::CH::EnergySkimLowDiscriminator, ch);
|
|
FillSpinBoxValueFromMemory(spbEnergySkimHigh[ID][ch], PHA::CH::EnergySkimHighDiscriminator, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbAnaProbe0[ID][ch], PHA::CH::WaveAnalogProbe0, ch);
|
|
FillComboBoxValueFromMemory(cbbAnaProbe1[ID][ch], PHA::CH::WaveAnalogProbe1, ch);
|
|
FillComboBoxValueFromMemory(cbbDigProbe0[ID][ch], PHA::CH::WaveDigitalProbe0, ch);
|
|
FillComboBoxValueFromMemory(cbbDigProbe1[ID][ch], PHA::CH::WaveDigitalProbe1, ch);
|
|
FillComboBoxValueFromMemory(cbbDigProbe2[ID][ch], PHA::CH::WaveDigitalProbe2, ch);
|
|
FillComboBoxValueFromMemory(cbbDigProbe3[ID][ch], PHA::CH::WaveDigitalProbe3, ch);
|
|
|
|
std::string itlConnect = digi[ID]->GetSettingValueFromMemory(PHA::CH::ITLConnect, ch);
|
|
if( itlConnect == "Disabled" ) {
|
|
ITLConnectStatus[ID][ch] = 0;
|
|
chITLConnect[ID][ch][0]->setStyleSheet("");
|
|
chITLConnect[ID][ch][1]->setStyleSheet("");
|
|
}
|
|
if( itlConnect == "ITLA" ) {
|
|
ITLConnectStatus[ID][ch] = 1;
|
|
chITLConnect[ID][ch][0]->setStyleSheet("background-color : green;");
|
|
chITLConnect[ID][ch][1]->setStyleSheet("");
|
|
}
|
|
if( itlConnect == "ITLB" ) {
|
|
ITLConnectStatus[ID][ch] = 2;
|
|
chITLConnect[ID][ch][0]->setStyleSheet("");
|
|
chITLConnect[ID][ch][1]->setStyleSheet("background-color : green;");
|
|
}
|
|
|
|
if( digi[ID]->GetFPGAType() == DPPType::PHA ) {
|
|
|
|
FillSpinBoxValueFromMemory(spbInputRiseTime[ID][ch], PHA::CH::TimeFilterRiseTime, ch);
|
|
FillSpinBoxValueFromMemory(spbTriggerGuard[ID][ch], PHA::CH::TimeFilterRetriggerGuard, ch);
|
|
FillComboBoxValueFromMemory(cbbLowFilter[ID][ch], PHA::CH::EnergyFilterLowFreqFilter, ch);
|
|
|
|
FillSpinBoxValueFromMemory(spbTrapRiseTime[ID][ch], PHA::CH::EnergyFilterRiseTime, ch);
|
|
FillSpinBoxValueFromMemory(spbTrapFlatTop[ID][ch], PHA::CH::EnergyFilterFlatTop, ch);
|
|
FillSpinBoxValueFromMemory(spbTrapPoleZero[ID][ch], PHA::CH::EnergyFilterPoleZero, ch);
|
|
|
|
FillSpinBoxValueFromMemory(spbPeaking[ID][ch], PHA::CH::EnergyFilterPeakingPosition, ch);
|
|
FillSpinBoxValueFromMemory(spbBaselineGuard[ID][ch], PHA::CH::EnergyFilterBaselineGuard, ch);
|
|
FillSpinBoxValueFromMemory(spbPileupGuard[ID][ch], PHA::CH::EnergyFilterPileUpGuard, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbBaselineAvg[ID][ch], PHA::CH::EnergyFilterBaselineAvg, ch);
|
|
FillSpinBoxValueFromMemory(spbFineGain[ID][ch], PHA::CH::EnergyFilterFineGain, ch);
|
|
FillComboBoxValueFromMemory(cbbPeakingAvg[ID][ch], PHA::CH::EnergyFilterPeakingAvg, ch);
|
|
|
|
}
|
|
|
|
if( digi[ID]->GetFPGAType() == DPPType::PSD){
|
|
|
|
FillComboBoxValueFromMemory(cbbADCInputBaselineAvg[ID][ch], PSD::CH::ADCInputBaselineAvg, ch);
|
|
FillSpinBoxValueFromMemory(spbAbsBaseline[ID][ch], PSD::CH::AbsoluteBaseline, ch);
|
|
FillSpinBoxValueFromMemory(spbADCInputBaselineGuard[ID][ch], PSD::CH::ADCInputBaselineGuard, ch);
|
|
|
|
FillComboBoxValueFromMemory(cbbTriggerFilter[ID][ch], PSD::CH::TriggerFilterSelection, ch);
|
|
FillComboBoxValueFromMemory(cbbTriggerHysteresis[ID][ch], PSD::CH::TriggerHysteresis, ch);
|
|
FillSpinBoxValueFromMemory(spbCFDDelay[ID][ch], PSD::CH::CFDDelay, ch);
|
|
FillSpinBoxValueFromMemory(spbCFDFraction[ID][ch], PSD::CH::CFDFraction, ch);
|
|
FillComboBoxValueFromMemory(cbbSmoothingFactor[ID][ch], PSD::CH::SmoothingFactor, ch);
|
|
FillComboBoxValueFromMemory(cbbChargeSmooting[ID][ch], PSD::CH::ChargeSmoothing, ch);
|
|
FillComboBoxValueFromMemory(cbbTimeFilterSmoothing[ID][ch], PSD::CH::TimeFilterSmoothing, ch);
|
|
FillSpinBoxValueFromMemory(spbTimeFilterReTriggerGuard[ID][ch], PSD::CH::TimeFilterRetriggerGuard, ch);
|
|
FillSpinBoxValueFromMemory(spbPileupGap[ID][ch], PSD::CH::PileupGap, ch);
|
|
|
|
FillSpinBoxValueFromMemory(spbGateLong[ID][ch], PSD::CH::GateLongLength, ch);
|
|
FillSpinBoxValueFromMemory(spbGateShort[ID][ch], PSD::CH::GateShortLength, ch);
|
|
FillSpinBoxValueFromMemory(spbGateOffset[ID][ch], PSD::CH::GateOffset, ch);
|
|
FillSpinBoxValueFromMemory(spbLongChargeIntergratorPedestal[ID][ch], PSD::CH::LongChargeIntegratorPedestal, ch);
|
|
FillSpinBoxValueFromMemory(spbShortChargeIntergratorPedestal[ID][ch], PSD::CH::ShortChargeIntegratorPedestal, ch);
|
|
FillComboBoxValueFromMemory(cbbEnergyGain[ID][ch], PSD::CH::EnergyGain, ch);
|
|
|
|
FillSpinBoxValueFromMemory(spbNeutronThreshold[ID][ch], PSD::CH::NeutronThreshold, ch);
|
|
FillComboBoxValueFromMemory(cbbEventNeutronReject[ID][ch], PSD::CH::EventNeutronReject, ch);
|
|
FillComboBoxValueFromMemory(cbbWaveNeutronReject[ID][ch], PSD::CH::WaveNeutronReject, ch);
|
|
}
|
|
}
|
|
|
|
//------ Trigger Mask
|
|
if( cbChPick[ID]->currentData().toInt() < 0 ) {
|
|
unsigned long mask = Utility::TenBase(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, 0));
|
|
|
|
bool isSame = true;
|
|
for(int ch = 1; ch < digi[ID]->GetNChannels() ; ch ++){
|
|
unsigned long haha = Utility::TenBase(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, ch));
|
|
if( mask != haha) {
|
|
isSame = false;
|
|
leTriggerMask[ID][MaxNumberOfChannel]->setText("Diff. value");
|
|
break;
|
|
}
|
|
}
|
|
|
|
if( isSame ) leTriggerMask[ID][MaxNumberOfChannel]->setText("0x" + QString::number(mask, 16).toUpper());
|
|
}else{
|
|
unsigned long mask = Utility::TenBase(digi[ID]->GetSettingValueFromMemory(PHA::CH::ChannelsTriggerMask, cbChPick[ID]->currentData().toInt()));
|
|
leTriggerMask[ID][digi[ID]->GetNChannels()]->setText("0x" + QString::number(mask, 16).toUpper());
|
|
leTriggerMask[ID][digi[ID]->GetNChannels()]->setStyleSheet("");
|
|
}
|
|
|
|
enableSignalSlot = true;
|
|
|
|
ReadTriggerMap();
|
|
|
|
if( cbChPick[ID]->currentData().toInt() >= 0 ) return;
|
|
|
|
SyncComboBox(cbbOnOff , -1);
|
|
SyncSpinBox(spbDCOffset , -1);
|
|
SyncSpinBox(spbThreshold , -1);
|
|
SyncComboBox(cbbParity , -1);
|
|
SyncSpinBox(spbRecordLength , -1);
|
|
SyncSpinBox(spbPreTrigger , -1);
|
|
|
|
SyncComboBox(cbbWaveSource, -1);
|
|
SyncComboBox(cbbWaveRes, -1);
|
|
SyncComboBox(cbbWaveSave, -1);
|
|
|
|
SyncComboBox(cbbAnaProbe0, -1);
|
|
SyncComboBox(cbbAnaProbe1, -1);
|
|
SyncComboBox(cbbDigProbe0, -1);
|
|
SyncComboBox(cbbDigProbe1, -1);
|
|
SyncComboBox(cbbDigProbe2, -1);
|
|
SyncComboBox(cbbDigProbe3, -1);
|
|
|
|
SyncComboBox(cbbEventSelector, -1);
|
|
SyncComboBox(cbbWaveSelector , -1);
|
|
SyncSpinBox(spbEnergySkimHigh, -1);
|
|
SyncSpinBox(spbEnergySkimLow , -1);
|
|
|
|
SyncComboBox(cbbEvtTrigger , -1);
|
|
SyncComboBox(cbbWaveTrigger , -1);
|
|
SyncComboBox(cbbChVetoSrc , -1);
|
|
SyncComboBox(cbbCoinMask , -1);
|
|
SyncComboBox(cbbAntiCoinMask , -1);
|
|
SyncSpinBox(spbCoinLength , -1);
|
|
SyncSpinBox(spbADCVetoWidth , -1);
|
|
|
|
if( digi[ID]->GetFPGAType() == DPPType::PHA){
|
|
SyncSpinBox(spbInputRiseTime , -1);
|
|
SyncSpinBox(spbTriggerGuard , -1);
|
|
SyncComboBox(cbbLowFilter , -1);
|
|
|
|
SyncSpinBox(spbTrapRiseTime , -1);
|
|
SyncSpinBox(spbTrapFlatTop , -1);
|
|
SyncSpinBox(spbTrapPoleZero , -1);
|
|
|
|
SyncSpinBox(spbPeaking , -1);
|
|
SyncSpinBox(spbBaselineGuard , -1);
|
|
SyncSpinBox(spbPileupGuard , -1);
|
|
|
|
SyncComboBox(cbbBaselineAvg , -1);
|
|
SyncComboBox(cbbPeakingAvg , -1);
|
|
SyncSpinBox(spbFineGain , -1);
|
|
}
|
|
|
|
if( digi[ID]->GetFPGAType() == DPPType::PSD){
|
|
|
|
|
|
SyncComboBox(cbbADCInputBaselineAvg , -1);
|
|
SyncSpinBox(spbAbsBaseline , -1);
|
|
SyncSpinBox(spbADCInputBaselineGuard, -1);
|
|
|
|
SyncComboBox(cbbTriggerFilter , -1);
|
|
SyncComboBox(cbbTriggerHysteresis , -1);
|
|
SyncSpinBox(spbCFDDelay , -1);
|
|
SyncSpinBox(spbCFDFraction , -1);
|
|
SyncComboBox(cbbSmoothingFactor , -1);
|
|
SyncComboBox(cbbChargeSmooting , -1);
|
|
SyncComboBox(cbbTimeFilterSmoothing , -1);
|
|
SyncSpinBox(spbTimeFilterReTriggerGuard, -1);
|
|
SyncSpinBox(spbPileupGap , -1);
|
|
|
|
SyncSpinBox(spbGateLong , -1);
|
|
SyncSpinBox(spbGateShort , -1);
|
|
SyncSpinBox(spbGateOffset , -1);
|
|
SyncSpinBox(spbLongChargeIntergratorPedestal , -1);
|
|
SyncSpinBox(spbShortChargeIntergratorPedestal, -1);
|
|
SyncComboBox(cbbEnergyGain , -1);
|
|
|
|
SyncSpinBox(spbNeutronThreshold , -1);
|
|
SyncComboBox(cbbEventNeutronReject, -1);
|
|
SyncComboBox(cbbWaveNeutronReject , -1);
|
|
|
|
|
|
}
|
|
|
|
}
|
|
//^###########################################################################
|
|
|
|
void DigiSettingsPanel::SetStartSource(){
|
|
if( !enableSignalSlot ) return;
|
|
|
|
std::string value = "";
|
|
for( int i = 0; i < (int) PHA::DIG::StartSource.GetAnswers().size(); i++){
|
|
if( ckbStartSource[ID][i]->isChecked() ){
|
|
//printf("----- %s \n", DIGIPARA::DIG::StartSource.GetAnswers()[i].first.c_str());
|
|
if( value != "" ) value += " | ";
|
|
value += PHA::DIG::StartSource.GetAnswers()[i].first;
|
|
}
|
|
}
|
|
|
|
//printf("================ %s\n", value.c_str());
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::StartSource.GetPara());
|
|
msg += " = " + QString::fromStdString(value);
|
|
|
|
if( digi[ID]->WriteValue(PHA::DIG::StartSource, value) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
for( int i = 0; i < (int) PHA::DIG::StartSource.GetAnswers().size(); i++){
|
|
ckbStartSource[ID][i]->setStyleSheet("");
|
|
}
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
for( int i = 0; i < (int) PHA::DIG::StartSource.GetAnswers().size(); i++){
|
|
ckbStartSource[ID][i]->setStyleSheet("background-color : red");
|
|
}
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::SetGlobalTriggerSource(){
|
|
if( !enableSignalSlot ) return;
|
|
|
|
std::string value = "";
|
|
if( cbDACoutMode[ID]->currentData().toString().toStdString() != "Square") bdTestPulse[ID]->setEnabled(false);
|
|
for( int i = 0; i < (int) PHA::DIG::GlobalTriggerSource.GetAnswers().size(); i++){
|
|
if( ckbGlbTrgSource[ID][i]->isChecked() ){
|
|
//printf("----- %s \n", DIGIPARA::DIG::StartSource.GetAnswers()[i].first.c_str());
|
|
if( value != "" ) value += " | ";
|
|
value += PHA::DIG::GlobalTriggerSource.GetAnswers()[i].first;
|
|
if( PHA::DIG::GlobalTriggerSource.GetAnswers()[i].first == "TestPulse" ) bdTestPulse[ID]->setEnabled(true);
|
|
}
|
|
}
|
|
|
|
//printf("================ %s\n", value.c_str());
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(PHA::DIG::GlobalTriggerSource.GetPara());
|
|
msg += " = " + QString::fromStdString(value);
|
|
SendLogMsg(msg);
|
|
|
|
if( digi[ID]->WriteValue(PHA::DIG::GlobalTriggerSource, value) ){
|
|
SendLogMsg(msg + "|OK.");
|
|
for( int i = 0; i < (int) PHA::DIG::GlobalTriggerSource.GetAnswers().size(); i++){
|
|
ckbGlbTrgSource[ID][i]->setStyleSheet("");
|
|
}
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
for( int i = 0; i < (int) PHA::DIG::GlobalTriggerSource.GetAnswers().size(); i++){
|
|
ckbGlbTrgSource[ID][i]->setStyleSheet("background-color : red");
|
|
}
|
|
}
|
|
|
|
}
|
|
|
|
|
|
//^###########################################################################
|
|
void DigiSettingsPanel::SetupShortComboBox(RComboBox *&cbb, Reg para){
|
|
for( int i = 0 ; i < (int) para.GetAnswers().size(); i++){
|
|
cbb->addItem(QString::fromStdString((para.GetAnswers())[i].second),
|
|
QString::fromStdString((para.GetAnswers())[i].first));
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::SetupComboBox(RComboBox *&cbb, const Reg para, int ch_index, bool isMaster, QString labelTxt, QGridLayout *layout, int row, int col, int srow, int scol){
|
|
QLabel * lb = new QLabel(labelTxt, this);
|
|
layout->addWidget(lb, row, col);
|
|
lb->setAlignment(Qt::AlignRight | Qt::AlignCenter);
|
|
cbb = new RComboBox(this);
|
|
layout->addWidget(cbb, row, col+1, srow, scol);
|
|
for( int i = 0 ; i < (int) para.GetAnswers().size(); i++){
|
|
cbb->addItem(QString::fromStdString((para.GetAnswers())[i].second), QString::fromStdString((para.GetAnswers())[i].first));
|
|
}
|
|
if( ch_index == -1 && para.GetType() == TYPE::CH ) cbb->addItem("");
|
|
connect(cbb, &RComboBox::currentIndexChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
int index = ( ch_index == -1 && isMaster ? cbChPick[ID]->currentData().toInt() : ch_index);
|
|
//int index = ch_index;
|
|
//printf("%s %d %s \n", para.GetPara().c_str(), index, cbb->currentData().toString().toStdString().c_str());
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara());
|
|
if( para.GetType() == TYPE::CH ) msg += ",CH:" + (index == -1 ? "All" : QString::number(index));
|
|
if( para.GetType() == TYPE::VGA ) msg += ",VGA:" + QString::number(index);
|
|
msg += " = " + cbb->currentData().toString();
|
|
if( digi[ID]->WriteValue(para, cbb->currentData().toString().toStdString(), index)){
|
|
SendLogMsg(msg + "|OK.");
|
|
cbb->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
cbb->setStyleSheet("color:red;");
|
|
}
|
|
});
|
|
}
|
|
|
|
void DigiSettingsPanel::SetupSpinBox(RSpinBox *&spb, const Reg para, int ch_index, bool isMaster, QString labelTxt, QGridLayout *layout, int row, int col, int srow, int scol){
|
|
QLabel * lb = new QLabel(labelTxt, this);
|
|
layout->addWidget(lb, row, col);
|
|
lb->setAlignment(Qt::AlignRight| Qt::AlignCenter);
|
|
spb = new RSpinBox(this);
|
|
if( isMaster ){
|
|
spb->setMinimum(qMin(-1.0, atof( para.GetAnswers()[0].first.c_str())));
|
|
}else{
|
|
spb->setMinimum(atof( para.GetAnswers()[0].first.c_str()));
|
|
}
|
|
spb->setMaximum(atof( para.GetAnswers()[1].first.c_str()));
|
|
|
|
if( para.GetAnswers().size() >= 3 ) {
|
|
spb->setSingleStep(atof(para.GetAnswers()[2].first.c_str()));
|
|
}else{
|
|
printf("--- missed. %s\n", para.GetPara().c_str());
|
|
}
|
|
spb->SetToolTip( atof( para.GetAnswers()[0].first.c_str()));
|
|
layout->addWidget(spb, row, col + 1, srow, scol);
|
|
|
|
connect(spb, &RSpinBox::valueChanged, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
spb->setStyleSheet("color:blue;");
|
|
});
|
|
connect(spb, &RSpinBox::returnPressed, this, [=](){
|
|
if( !enableSignalSlot ) return;
|
|
//printf("%s %d %d \n", para.GetPara().c_str(), index, spb->value());
|
|
if( spb->decimals() == 0 && spb->singleStep() != 1) {
|
|
double step = spb->singleStep();
|
|
double value = spb->value();
|
|
spb->setValue( (std::round(value/step) * step) );
|
|
}
|
|
int index = ( ch_index == -1 && isMaster ? cbChPick[ID]->currentData().toInt() : ch_index);
|
|
QString msg;
|
|
msg = "DIG:"+ QString::number(digi[ID]->GetSerialNumber()) + "|" + QString::fromStdString(para.GetPara()) ;
|
|
if( para.GetType() == TYPE::CH ) msg += ",CH:" + (index == -1 ? "All" : QString::number(index));
|
|
msg += " = " + QString::number(spb->value());
|
|
|
|
if( para.GetPara() == PHA::GROUP::InputDelay.GetPara() ){
|
|
|
|
if( digi[ID]->WriteValue(para, std::to_string(spb->value()/8), index)){
|
|
SendLogMsg(msg + "|OK.");
|
|
spb->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
spb->setStyleSheet("color:red;");
|
|
}
|
|
|
|
// printf("============%d| %s \n", index, digi[ID]->GetSettingValueFromMemory(PHA::GROUP::InputDelay, index).c_str());
|
|
|
|
|
|
}else{
|
|
if( digi[ID]->WriteValue(para, std::to_string(spb->value()), index)){
|
|
SendLogMsg(msg + "|OK.");
|
|
spb->setStyleSheet("");
|
|
UpdatePanelFromMemory();
|
|
UpdateOtherPanels();
|
|
}else{
|
|
SendLogMsg(msg + "|Fail.");
|
|
spb->setStyleSheet("color:red;");
|
|
}
|
|
}
|
|
});
|
|
}
|
|
|
|
void DigiSettingsPanel::SyncComboBox(RComboBox *(&cbb)[][MaxNumberOfChannel + 1], int ch){
|
|
if( !enableSignalSlot ) return;
|
|
if( cbChPick[ID]->currentData().toInt() >= 0 ) return;
|
|
|
|
const int nCh = digi[ID]->GetNChannels();
|
|
|
|
if( ch == nCh ){
|
|
const int index = cbb[ID][nCh]->currentIndex();
|
|
if( cbb[ID][nCh]->currentText() == "" ) return;
|
|
enableSignalSlot = false;
|
|
for( int i = 0; i < nCh; i++) cbb[ID][i]->setCurrentIndex(index);
|
|
enableSignalSlot = true;
|
|
}else{
|
|
//check is all ComboBox has same index;
|
|
int count = 1;
|
|
const int index = cbb[ID][0]->currentIndex();
|
|
for( int i = 1; i < nCh; i ++){
|
|
if( cbb[ID][i]->currentIndex() == index ) count++;
|
|
}
|
|
|
|
enableSignalSlot = false;
|
|
if( count != nCh ){
|
|
cbb[ID][nCh]->setCurrentText("");
|
|
}else{
|
|
cbb[ID][nCh]->setCurrentIndex(index);
|
|
}
|
|
enableSignalSlot = true;
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::SyncSpinBox(RSpinBox *(&spb)[][MaxNumberOfChannel+1], int ch){
|
|
if( !enableSignalSlot ) return;
|
|
|
|
const int nCh = digi[ID]->GetNChannels();
|
|
|
|
if( ch == nCh ){
|
|
const int value = spb[ID][nCh]->value();
|
|
if( spb[ID][nCh]->value() == -999 ) return;
|
|
enableSignalSlot = false;
|
|
for( int i = 0; i < nCh; i++) spb[ID][i]->setValue(value);
|
|
enableSignalSlot = true;
|
|
}else{
|
|
//check is all ComboBox has same index;
|
|
int count = 1;
|
|
const int value = spb[ID][0]->value();
|
|
for( int i = 1; i < nCh; i ++){
|
|
if( spb[ID][i]->value() == value ) count++;
|
|
}
|
|
|
|
//printf("%d =? %d \n", count, nCh);
|
|
enableSignalSlot = false;
|
|
if( count != nCh ){
|
|
spb[ID][nCh]->setValue(-1);
|
|
}else{
|
|
spb[ID][nCh]->setValue(value);
|
|
}
|
|
enableSignalSlot = true;
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::SetupSpinBoxTab(RSpinBox *(&spb)[][MaxNumberOfChannel+1], const Reg para, QString text, QTabWidget *tabWidget, int iDigi, int nChannel){
|
|
QWidget * tabPage = new QWidget(this); tabWidget->addTab(tabPage, text);
|
|
QGridLayout * allLayout = new QGridLayout(tabPage);
|
|
//allLayout->setAlignment(Qt::AlignTop | Qt::AlignHCenter);
|
|
allLayout->setAlignment(Qt::AlignTop);
|
|
allLayout->setHorizontalSpacing(10);
|
|
allLayout->setVerticalSpacing(0);
|
|
for( int ch = 0; ch < nChannel; ch++){
|
|
SetupSpinBox(spb[iDigi][ch], para, ch, false, "ch-"+QString::number(ch)+ " ", allLayout, ch/4, ch%4 * 2);
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::SetupComboBoxTab(RComboBox *(&cbb)[][MaxNumberOfChannel + 1], const Reg para, QString text, QTabWidget *tabWidget, int iDigi, int nChannel, int nCol){
|
|
QWidget * tabPage = new QWidget(this); tabWidget->addTab(tabPage, text);
|
|
QGridLayout * allLayout = new QGridLayout(tabPage);
|
|
//allLayout->setAlignment(Qt::AlignTop | Qt::AlignHCenter);
|
|
allLayout->setAlignment(Qt::AlignTop);
|
|
allLayout->setHorizontalSpacing(10);
|
|
allLayout->setVerticalSpacing(0);
|
|
for( int ch = 0; ch < nChannel; ch++){
|
|
SetupComboBox(cbb[iDigi][ch], para, ch, false, "ch-"+QString::number(ch) + " ", allLayout, ch/nCol, ch%nCol * 3);
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::FillComboBoxValueFromMemory(RComboBox *&cbb, const Reg para, int ch_index){
|
|
QString result = QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para, ch_index));
|
|
//printf("%s === %s, %d, %p\n", __func__, result.toStdString().c_str(), ID, cbb);
|
|
int index = cbb->findData(result);
|
|
if( index >= 0 && index < cbb->count()) {
|
|
cbb->setCurrentIndex(index);
|
|
}else{
|
|
//printf("%s %s\n", para.GetPara().c_str(), result.toStdString().c_str());
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::FillSpinBoxValueFromMemory(RSpinBox *&spb, const Reg para, int ch_index){
|
|
QString result = QString::fromStdString(digi[ID]->GetSettingValueFromMemory(para, ch_index));
|
|
//printf("%s === %s, %d, %p\n", __func__, result.toStdString().c_str(), ID, spb);
|
|
|
|
if( para.GetPara() == PHA::GROUP::InputDelay.GetPara() && digi[ID]->GetCupVer() >= MIN_VERSION_GROUP) {
|
|
spb->setValue(result.toDouble()*8);
|
|
}else{
|
|
spb->setValue(result.toDouble());
|
|
}
|
|
}
|
|
|
|
void DigiSettingsPanel::ReadBoardSetting(int cbIndex){
|
|
|
|
if( enableSignalSlot == false ) return;
|
|
|
|
enableSignalSlot = false;
|
|
|
|
// PHA and PSD has same board setting, but for furture extension
|
|
int ID = cbIQDigi->currentIndex();
|
|
std::vector<Reg> bdSettings ;
|
|
|
|
if( digi[ID]->GetFPGAType() == DPPType::PHA ) {
|
|
bdSettings = PHA::DIG::AllSettings;
|
|
}else if( digi[ID]->GetFPGAType() == DPPType::PSD ) {
|
|
bdSettings = PSD::DIG::AllSettings;
|
|
}else{
|
|
enableSignalSlot = true;
|
|
return;
|
|
}
|
|
|
|
QString type;
|
|
switch (bdSettings[cbIndex].ReadWrite()) {
|
|
case RW::ReadOnly : type ="Read Only"; break;
|
|
case RW::WriteOnly : type ="Write Only"; break;
|
|
case RW::ReadWrite : type ="Read/Write"; break;
|
|
}
|
|
leBdSettingsType->setText(type);
|
|
|
|
QString ans = QString::fromStdString(digi[ID]->ReadValue(bdSettings[cbIndex]));
|
|
ANSTYPE haha = bdSettings[cbIndex].GetAnswerType();
|
|
|
|
if( haha == ANSTYPE::BYTE){
|
|
leBdSettingsRead->setText( "0x" + QString::number(ans.toULong(), 16).rightJustified(16, '0'));
|
|
}else if( haha == ANSTYPE::BINARY ){
|
|
leBdSettingsRead->setText( "0b" + QString::number(ans.toUInt(), 2).rightJustified(18, '0'));
|
|
}else{
|
|
leBdSettingsRead->setText(ans);
|
|
}
|
|
leBdSettingsUnit->setText(QString::fromStdString(bdSettings[cbIndex].GetUnit()));
|
|
|
|
if( bdSettings[cbIndex].ReadWrite() != RW::ReadOnly && haha != ANSTYPE::NONE ){
|
|
|
|
//===== spin box
|
|
if( haha == ANSTYPE::FLOAT || haha == ANSTYPE::INTEGER ){
|
|
cbBdAns->clear();
|
|
cbBdAns->setEnabled(false);
|
|
leBdSettingsWrite->setEnabled(false);
|
|
leBdSettingsWrite->clear();
|
|
sbBdSettingsWrite->setEnabled(true);
|
|
sbBdSettingsWrite->setMinimum(atof(bdSettings[cbIndex].GetAnswers()[0].first.c_str()));
|
|
sbBdSettingsWrite->setMaximum(atof(bdSettings[cbIndex].GetAnswers()[1].first.c_str()));
|
|
sbBdSettingsWrite->setSingleStep(atof(bdSettings[cbIndex].GetAnswers()[2].first.c_str()));
|
|
sbBdSettingsWrite->setValue(00);
|
|
sbBdSettingsWrite->setDecimals(0);
|
|
}
|
|
if( haha == ANSTYPE::FLOAT) sbBdSettingsWrite->setDecimals(3);
|
|
//===== combo Box
|
|
if( haha == ANSTYPE::COMBOX){
|
|
cbBdAns->setEnabled(true);
|
|
cbBdAns->clear();
|
|
int ansIndex = -1;
|
|
QString ans2 = "";
|
|
for( int i = 0; i < (int) bdSettings[cbIndex].GetAnswers().size(); i++){
|
|
cbBdAns->addItem(QString::fromStdString(bdSettings[cbIndex].GetAnswers()[i].second),
|
|
QString::fromStdString(bdSettings[cbIndex].GetAnswers()[i].first));
|
|
|
|
if( ans == QString::fromStdString(bdSettings[cbIndex].GetAnswers()[i].first)) {
|
|
ansIndex = i;
|
|
ans2 = QString::fromStdString(bdSettings[cbIndex].GetAnswers()[i].second);
|
|
}
|
|
}
|
|
cbBdAns->setCurrentIndex(ansIndex);
|
|
leBdSettingsRead->setText( ans + " [ " + ans2 + " ]");
|
|
sbBdSettingsWrite->setEnabled(false);
|
|
sbBdSettingsWrite->setStyleSheet("");
|
|
sbBdSettingsWrite->setValue(0);
|
|
leBdSettingsWrite->setEnabled(false);
|
|
leBdSettingsWrite->setText(ans);
|
|
}
|
|
//===== lineEdit
|
|
if( haha == ANSTYPE::STR || haha == ANSTYPE::BYTE || haha == ANSTYPE::BINARY){
|
|
cbBdAns->clear();
|
|
cbBdAns->setEnabled(false);
|
|
leBdSettingsWrite->setEnabled(true);
|
|
leBdSettingsWrite->clear();
|
|
sbBdSettingsWrite->setEnabled(false);
|
|
sbBdSettingsWrite->setStyleSheet("");
|
|
sbBdSettingsWrite->setValue(0);
|
|
}
|
|
}else{
|
|
cbBdAns->clear();
|
|
cbBdAns->setEnabled(false);
|
|
sbBdSettingsWrite->setEnabled(false);
|
|
sbBdSettingsWrite->setStyleSheet("");
|
|
sbBdSettingsWrite->cleanText();
|
|
leBdSettingsWrite->setEnabled(false);
|
|
leBdSettingsWrite->clear();
|
|
}
|
|
|
|
if( bdSettings[cbIndex].GetPara() == PHA::DIG::StartSource.GetPara()
|
|
|| bdSettings[cbIndex].GetPara() == PHA::DIG::GlobalTriggerSource.GetPara() ){
|
|
|
|
leBdSettingsWrite->setEnabled(true);
|
|
leBdSettingsWrite->clear();
|
|
}
|
|
|
|
enableSignalSlot = true;
|
|
}
|
|
|
|
void DigiSettingsPanel::ReadChannelSetting(int cbIndex){
|
|
|
|
if( enableSignalSlot == false ) return;
|
|
enableSignalSlot = false;
|
|
|
|
int ID = cbIQDigi->currentIndex();
|
|
std::vector<Reg> chSettings ;
|
|
|
|
if( digi[ID]->GetFPGAType() == DPPType::PHA ) {
|
|
chSettings = PHA::CH::AllSettings;
|
|
}else if( digi[ID]->GetFPGAType() == DPPType::PSD ) {
|
|
chSettings = PSD::CH::AllSettings;
|
|
}else{
|
|
enableSignalSlot = true;
|
|
return;
|
|
}
|
|
|
|
QString type;
|
|
switch (chSettings[cbIndex].ReadWrite()) {
|
|
case RW::ReadOnly : type ="Read Only"; break;
|
|
case RW::WriteOnly : type ="Write Only"; break;
|
|
case RW::ReadWrite : type ="Read/Write"; break;
|
|
}
|
|
leChSettingsType->setText(type);
|
|
|
|
QString ans = QString::fromStdString(digi[ID]->ReadValue(chSettings[cbIndex], cbIQCh->currentData().toInt()));
|
|
ANSTYPE haha = chSettings[cbIndex].GetAnswerType();
|
|
|
|
if( haha == ANSTYPE::BYTE){
|
|
leChSettingsRead->setText( "0x" + QString::number(ans.toULong(), 16).rightJustified(16, '0'));
|
|
}else if( haha == ANSTYPE::BINARY ){
|
|
leChSettingsRead->setText( "0b" + QString::number(ans.toUInt(), 2).rightJustified(18, '0'));
|
|
}else{
|
|
leChSettingsRead->setText(ans);
|
|
}
|
|
|
|
leChSettingsUnit->setText(QString::fromStdString(chSettings[cbIndex].GetUnit()));
|
|
|
|
|
|
if( chSettings[cbIndex].ReadWrite() != RW::ReadOnly && haha != ANSTYPE::NONE ){
|
|
|
|
if( haha == ANSTYPE::FLOAT || haha == ANSTYPE::INTEGER ){
|
|
cbChSettingsWrite->clear();
|
|
cbChSettingsWrite->setEnabled(false);
|
|
leChSettingsWrite->setEnabled(false);
|
|
leChSettingsWrite->clear();
|
|
sbChSettingsWrite->setEnabled(true);
|
|
sbChSettingsWrite->setMinimum(atof(chSettings[cbIndex].GetAnswers()[0].first.c_str()));
|
|
sbChSettingsWrite->setMaximum(atof(chSettings[cbIndex].GetAnswers()[1].first.c_str()));
|
|
sbChSettingsWrite->setSingleStep(atof(chSettings[cbIndex].GetAnswers()[2].first.c_str()));
|
|
sbChSettingsWrite->setValue(ans.toFloat());
|
|
sbChSettingsWrite->setDecimals(3);
|
|
}
|
|
if( haha == ANSTYPE::INTEGER) sbBdSettingsWrite->setDecimals(0);
|
|
if( haha == ANSTYPE::COMBOX){
|
|
cbChSettingsWrite->setEnabled(true);
|
|
cbChSettingsWrite->clear();
|
|
int ansIndex = -1;
|
|
QString ans2 = "";
|
|
for( int i = 0; i < (int) chSettings[cbIndex].GetAnswers().size(); i++){
|
|
cbChSettingsWrite->addItem(QString::fromStdString(chSettings[cbIndex].GetAnswers()[i].second),
|
|
QString::fromStdString(chSettings[cbIndex].GetAnswers()[i].first));
|
|
|
|
if( ans == QString::fromStdString(chSettings[cbIndex].GetAnswers()[i].first)) {
|
|
ansIndex = i;
|
|
ans2 = QString::fromStdString(chSettings[cbIndex].GetAnswers()[i].second);
|
|
}
|
|
}
|
|
cbChSettingsWrite->setCurrentIndex(ansIndex);
|
|
leChSettingsRead->setText( ans + " [ " + ans2 + " ]");
|
|
sbChSettingsWrite->setEnabled(false);
|
|
sbChSettingsWrite->setStyleSheet("");
|
|
sbChSettingsWrite->setValue(0);
|
|
leChSettingsWrite->setEnabled(false);
|
|
leChSettingsWrite->setText(ans2);
|
|
}
|
|
if( haha == ANSTYPE::STR || haha == ANSTYPE::BYTE || haha == ANSTYPE::BINARY){
|
|
cbChSettingsWrite->clear();
|
|
cbChSettingsWrite->setEnabled(false);
|
|
leChSettingsWrite->setEnabled(true);
|
|
leChSettingsWrite->clear();
|
|
sbChSettingsWrite->setEnabled(false);
|
|
sbChSettingsWrite->setStyleSheet("");
|
|
sbChSettingsWrite->setValue(0);
|
|
}
|
|
}else{
|
|
cbChSettingsWrite->clear();
|
|
cbChSettingsWrite->setEnabled(false);
|
|
sbChSettingsWrite->setEnabled(false);
|
|
sbChSettingsWrite->setStyleSheet("");
|
|
sbChSettingsWrite->cleanText();
|
|
leChSettingsWrite->setEnabled(false);
|
|
leChSettingsWrite->clear();
|
|
}
|
|
|
|
enableSignalSlot = true;
|
|
}
|
|
|
|
bool DigiSettingsPanel::CheckDigitizersCanCopy(){
|
|
int digiFromIndex = cbCopyDigiFrom->currentIndex();
|
|
int digiToIndex = cbCopyDigiTo->currentIndex();
|
|
if( digi[digiFromIndex]->GetModelName() != digi[digiToIndex]->GetModelName() ) return false;
|
|
if( digi[digiFromIndex]->GetFPGAType() != digi[digiToIndex]->GetFPGAType() ) return false;
|
|
if( digi[digiFromIndex]->GetFPGAVersion() != digi[digiToIndex]->GetFPGAVersion() ) return false;
|
|
return true;
|
|
}
|
|
|
|
void DigiSettingsPanel::CheckRadioAndCheckedButtons(){
|
|
|
|
int chFromIndex = -1;
|
|
for( int i = 0 ; i < MaxNumberOfChannel ; i++){
|
|
rbCopyChFrom[i]->setStyleSheet("");
|
|
if( rbCopyChFrom[i]->isChecked() && cbCopyDigiFrom->currentIndex() == cbCopyDigiTo->currentIndex()){
|
|
chFromIndex = i;
|
|
rbCopyChFrom[i]->setStyleSheet("color : red;");
|
|
chkChTo[i]->setChecked(false);
|
|
chkChTo[i]->setStyleSheet("");
|
|
}
|
|
}
|
|
|
|
for( int i = 0 ; i < MaxNumberOfChannel ; i++) chkChTo[i]->setEnabled(true);
|
|
if( chFromIndex >= 0 && cbCopyDigiFrom->currentIndex() == cbCopyDigiTo->currentIndex() ) chkChTo[chFromIndex]->setEnabled(false);
|
|
|
|
bool isToIndexCleicked = false;
|
|
for( int i = 0 ; i < MaxNumberOfChannel ; i++){
|
|
if( chkChTo[i]->isChecked() ){
|
|
isToIndexCleicked = true;
|
|
chkChTo[i]->setStyleSheet("color : blue;");
|
|
}else{
|
|
chkChTo[i]->setStyleSheet("");
|
|
}
|
|
}
|
|
|
|
pbCopyChannel->setEnabled(chFromIndex >= 0 && isToIndexCleicked );
|
|
}
|
|
|
|
bool DigiSettingsPanel::CopyChannelSettings(int digiFrom, int chFrom, int digiTo, int chTo){
|
|
|
|
if( !CheckDigitizersCanCopy() ) return false;
|
|
|
|
SendLogMsg("Copy Settings from DIG:" + QString::number(digi[digiFrom]->GetSerialNumber()) + ", CH:" + QString::number(chFrom) + " ---> DIG:" + QString::number(digi[digiTo]->GetSerialNumber()) + ", CH:" + QString::number(chTo));
|
|
for( int k = 0; k < (int) PHA::CH::AllSettings.size(); k ++){
|
|
if( PHA::CH::AllSettings[k].ReadWrite() != RW::ReadWrite ) continue;
|
|
std::string haha = digi[digiFrom]->GetSettingValueFromMemory(PHA::CH::AllSettings[k], chFrom);
|
|
if( !digi[digiTo]->WriteValue( PHA::CH::AllSettings[k], haha , chTo ) ){
|
|
SendLogMsg("something wrong when copying setting : " + QString::fromStdString( PHA::CH::AllSettings[k].GetPara())) ;
|
|
return false;
|
|
break;
|
|
}
|
|
}
|
|
return true;
|
|
}
|
|
|
|
bool DigiSettingsPanel::CopyBoardSettings(){
|
|
int digiFromIndex = cbCopyDigiFrom->currentIndex();
|
|
int digiToIndex = cbCopyDigiTo->currentIndex();
|
|
|
|
if( !CheckDigitizersCanCopy() ) return false;
|
|
|
|
SendLogMsg("Copy Settings from DIG:" + QString::number(digi[digiFromIndex]->GetSerialNumber()) + " to DIG:" + QString::number(digi[digiToIndex]->GetSerialNumber()));
|
|
for( int i = 0; i < MaxNumberOfChannel; i++){
|
|
if( chkChTo[i]->isChecked() ){
|
|
//Copy setting
|
|
for( int k = 0; k < (int) PHA::DIG::AllSettings.size(); k ++){
|
|
if( PHA::DIG::AllSettings[k].ReadWrite() != RW::ReadWrite ) continue;
|
|
if( ! digi[digiToIndex]->WriteValue( PHA::DIG::AllSettings[k], digi[digiFromIndex]->GetSettingValueFromMemory(PHA::DIG::AllSettings[k])) ){
|
|
SendLogMsg("something wrong when copying setting : " + QString::fromStdString( PHA::DIG::AllSettings[k].GetPara())) ;
|
|
return false;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
SendLogMsg("------ done");
|
|
return true;
|
|
}
|
|
|
|
bool DigiSettingsPanel::CopyWholeDigitizer(){
|
|
if( !CopyBoardSettings() ) return false;
|
|
|
|
int digiTo = cbCopyDigiTo->currentIndex();
|
|
|
|
for( int ch = 0; ch < digi[ID]->GetNChannels() ; ch ++){
|
|
if ( ! CopyChannelSettings(cbCopyDigiFrom->currentIndex(), ch, digiTo, ch ) ) return false;
|
|
}
|
|
|
|
return true;
|
|
}
|