Water Cooling System - Revision history

Rtang at 22:13, 8 April 2022

2022-04-08T22:13:47Z

← Older revision		Revision as of 18:13, 8 April 2022
Line 2:		Line 2:
	[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]		[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]

	The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, [[Sputter Source]] (SNICS), [[Tandem]] are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.		The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, [[Ion Sources#Sputter Source\| Sputter Source]] (SNICS), [[Tandem]] are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.

Rtang at 21:57, 8 April 2022

2022-04-08T21:57:23Z

← Older revision		Revision as of 17:57, 8 April 2022
Line 2:		Line 2:
	[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]		[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]

	The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, Sputter Source (SNICS), Tandem are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.		The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, [[Sputter Source]] (SNICS), [[Tandem]] are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.

Rtang: /* Recirculator Pump Goes Off and Will Not Restart */

2022-04-08T21:55:24Z

Recirculator Pump Goes Off and Will Not Restart

← Older revision		Revision as of 17:55, 8 April 2022
Line 12:		Line 12:

	== Recirculator Pump Goes Off and Will Not Restart ==		== Recirculator Pump Goes Off and Will Not Restart ==
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in ~~the Gas Handling Room~~ [[:File:GasHandlingRoomLayout.png]] (see Figure). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in [[:File:GasHandlingRoomLayout.png\| the Gas Handling Room ]] (see Figure). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

Rtang: /* Recirculator Pump Goes Off and Will Not Restart */

2022-04-08T21:54:44Z

Recirculator Pump Goes Off and Will Not Restart

← Older revision		Revision as of 17:54, 8 April 2022
Line 12:		Line 12:

	== Recirculator Pump Goes Off and Will Not Restart ==		== Recirculator Pump Goes Off and Will Not Restart ==
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see Figure). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room [[:File:GasHandlingRoomLayout.png]] (see Figure). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

Rtang: /* Recirculator Pump Goes Off and Will Not Restart */

2022-04-08T21:51:52Z

Recirculator Pump Goes Off and Will Not Restart

← Older revision		Revision as of 17:51, 8 April 2022
Line 12:		Line 12:

	== Recirculator Pump Goes Off and Will Not Restart ==		== Recirculator Pump Goes Off and Will Not Restart ==
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see ~~figure 5~~). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see Figure). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

Rtang at 21:50, 8 April 2022

2022-04-08T21:50:19Z

← Older revision		Revision as of 17:50, 8 April 2022
Line 1:		Line 1:

			[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]

	The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, Sputter Source (SNICS), Tandem are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.		The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, Sputter Source (SNICS), Tandem are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.

	~~[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]~~

	== When Chilled Water Service is Interrupted ==		== When Chilled Water Service is Interrupted ==

Rtang at 21:50, 8 April 2022

2022-04-08T21:50:05Z

← Older revision		Revision as of 17:50, 8 April 2022
Line 1:		Line 1:
	The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, Sputter Source (SNICS), Tandem are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.		The recirculating cooling water in the lab employs a heat exchanger, temperature-controlled valve, filter and pump to provide cold water service to equipment. Bending magnets, PIN Diode Pulsars, Sputter Source (SNICS), Tandem are some of the equipment that require cooling to remain in operation. The recirculating loop is automatically topped off by city or chilled water depending on availability. Should there be an interruption of water service to the building the following instructions apply. The valves are located in the Southeast corner of the Tandem Vault.

			[[File:GasHandlingRoomLayout.png\|600px\|thumb\|right]]

	== When Chilled Water Service is Interrupted ==		== When Chilled Water Service is Interrupted ==
Line 9:		Line 11:
	== Recirculator Pump Goes Off and Will Not Restart ==		== Recirculator Pump Goes Off and Will Not Restart ==
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

	~~[[File:GasHandlingRoomLayout.png\|thumb]]~~

Rtang: /* Recirculator Pump Goes Off and Will Not Restart */

2022-04-08T21:49:39Z

Recirculator Pump Goes Off and Will Not Restart

← Older revision		Revision as of 17:49, 8 April 2022
Line 10:		Line 10:
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

	[[GasHandlingRoomLayout.png~~\|500px~~\|thumb~~\|right~~]]		[[File:GasHandlingRoomLayout.png\|thumb]]

Rtang: /* Recirculator Pump Goes Off and Will Not Restart */

2022-04-08T21:49:19Z

Recirculator Pump Goes Off and Will Not Restart

← Older revision		Revision as of 17:49, 8 April 2022
Line 10:		Line 10:
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

	[[~~File:GasHandingRoomLayout~~.png\|500px\|thumb\|right]]		[[GasHandlingRoomLayout.png\|500px\|thumb\|right]]

Rtang at 21:48, 8 April 2022

2022-04-08T21:48:45Z

← Older revision		Revision as of 17:48, 8 April 2022
Line 10:		Line 10:
	The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.		The recirculating loop can be fed directly by city water in an emergency situation. The valves C1 and D1 are located in the Southeast corner of the Tandem Vault. The valves C2, D2 and D3 are located in the Gas Handling Room (see figure 5). C2 and D3 are located by the L.E. vault entrance and D2 is located near the floor at the middle of the East wall. To bypass the recirculating loops water pump first ensure its power switch, positioned on the wall over the pump, is turned off. Close the valves C1 and C2. Open valve D1 and D2 first and then open D3. When the recirculator pump is operational again it should be placed back into service. Close valve D3 first and the close D1 and D2. Open valves C1 and C2. Now turn the recirculating pump back on. The system should now be providing cool water via the heat exchanger.

	[[File:GasHandingRoomLayout\|500px\|thumb\|right]]		[[File:GasHandingRoomLayout.png\|500px\|thumb\|right]]